MnCo改性的MCM-41催化剂用于氯苯催化燃烧的研究

引用本文: 成珍, 李敬荣, 杨鹏, 左树锋. MnCo改性的MCM-41催化剂用于氯苯催化燃烧的研究[J]. 催化学报, 2018, 39(4): 849-856. doi: 10.1016/S1872-2067(17)62950-4 shu

Citation: Zhen Cheng, Jingrong Li, Peng Yang, Shufeng Zuo. Preparation of MnCo/MCM-41 catalysts with high performance for chlorobenzene combustion[J]. Chinese Journal of Catalysis, 2018, 39(4): 849-856. doi: 10.1016/S1872-2067(17)62950-4 shu

MnCo改性的MCM-41催化剂用于氯苯催化燃烧的研究

绍兴文理学院, 浙江省精细化学品传统工艺替代技术研究重点实验室, 浙江绍兴 312000
基金项目:
国家自然科学基金（21577094）.

摘要: 含氯挥发性有机化合物（CVOCs）是对人体健康和环境危害极大的有机化合物.常见的有二氯乙烷、三氯乙烯、三氯甲烷、四氯化碳和氯苯等.有些CVOCs是"三致"（致畸、致癌、致突变）物质，有些少量进入大气就能破坏臭氧层，亦或与臭氧等形成光化学烟雾，引起全球变暖.因此，对于其消除迫在眉睫.CVOCs通常采用高温直接燃烧、吸附、光催化氧化和催化燃烧等方法降解.其中，催化燃烧是非常有效的.我们选择氯苯作为CVOCs探针分子是因其不仅存在于农药和化工产品中，在室内环境中也大量存在，而负载贵金属和非贵金属型催化剂可用于其催化降解.贵金属催化剂价格高而且易氯中毒，但过渡金属催化剂价格低且抗失活，因而是不错的选择.通常过渡金属催化剂使用V₂O₅，Cr₂O₃，MnO₂，Co₃O₄及NiO等活性组分，而Mn和Co氧化物有较好活性且没有环境污染，常用作活性组分.另外，MCM-41是有序介孔硅酸盐和硅铝酸盐家族中M41S的一员，具有高的比表面积和较窄的孔径分布，常用作催化剂的载体.我们利用具有大比表面积、大孔径的MCM-41作为载体，采用浸渍法负载MnO_x，CoO_x，MnO_x-CoO_x等活性组分，制备系列的催化剂用于低浓度氯苯的催化燃烧，研究催化剂的催化活性、选择性及稳定性.并利用XRD、N₂吸脱附、高分辨电镜-能谱分析、H₂-TPR和CB-TPD等手段对MCM-41及催化剂的织构-结构、表面形貌、活性组分分散状态、氧化还原性能及吸附性能等做了系统的研究.
采用表面活性剂软模板技术合成了具有大比表面积、大孔径、耐热稳定性高的MCM-41介孔分子筛，负载不同比例的Mn/Co（摩尔比是3：1、6：1及9：1，其中总负载量为10%），以氯苯催化燃烧为探针反应，筛选出活性最佳时的Mn/Co比例.活性评价实验结果表明，各催化剂的活性以下列顺序依次降低：MnCo（6：1）/MCM-41 > MnCo（9：1）/MCM-41 > MnCo（3：1）/MCM-41 > Mn/MCM-41 > Co/MCM-41，其中MnCo（6：1）/MCM-41活性最佳，在270℃即可完全催化燃烧氯苯.耐久性实验结果显示，MnCo（6：1）/MCM-41在连续反应1000h后，其活性没有降低，表明其具有非常良好的稳定性.XRD实验结果表明，在Mn/MCM-41及Co/MCM-41催化剂上分别检测到MnO₂及Co₃O₄的特征衍射峰.在MnCo（6：1）/MCM-41催化剂上，MnO₂及Co₃O₄的特征衍射峰消失，同时出现了MnCoO_x的特征衍射峰，这是由于MnO₂及Co₃O₄的强相互作用经过焙烧后形成的，且MnCoO_x的特征衍射峰较小，表明双金属活性组分的分散比单金属催化剂好.N₂吸脱附结果显示，MCM-41的比表面积达到805.9m²/g，孔体积达到0.795cm³/g.负载活性组分后其比表面积及孔体积均有不同程度的减小，这是由于活性组分进入了MCM-41的孔隙.高分辨电镜结果表明，MCM-41具有均匀的介孔孔道结构，MnCoO_x在MCM-41表面的颗粒小，分散好.能谱扫描出Mn，Co，O等元素，表明活性组分成功地负载在MCM-41载体上.H₂-TPR表明，双金属催化剂的还原峰温较单金属催化剂低，表明其具有更好的氧化性能.CB-TPD结果表明，MnCo双金属催化剂脱附氯苯的温度高于单金属催化剂，说明氯苯与催化剂之间的相互作用更强，即双金属催化剂对氯苯的吸附能力更强，使得氯苯催化燃烧更加充分，因此其催化性能更好.同时，深入探讨了MnO_x，CoO_x，MnCoO_x和MCM-41之间的相互作用及对催化燃烧性能的影响.

关键词:

MCM-41分子筛
/ Mn/Co
/ 催化燃烧
/ 氯苯
/ 表征

English

Preparation of MnCo/MCM-41 catalysts with high performance for chlorobenzene combustion

Zhejiang Key Laboratory of Alternative Technologies for Fine Chemicals Process, Shaoxing University, Shaoxing 312000, Zhejiang, China
Received Date: 18 November 2017
Revised Date: 25 December 2017
Fund Project:
This work was supported by the National Natural Science Foundation of China (21577094).

Abstract: MCM-41 was synthesized by a soft template technique. The specific surface area and pore volume of the MCM-41 were 805.9 m²/g and 0.795 cm³/g, respectively. MCM-41-supported manganese and cobalt oxide catalysts were prepared by an impregnation method. The energy dispersive X-ray spectroscopy clearly confirmed the existence of Mn, Co, and O, which indicated the successful loading of the active components on the surface of MCM-41. The structure and function of the catalysts were changed by modulating the molar ratio of manganese to cobalt. The 10%MnCo(6:1)/MCM-41 (Mn/Co molar ratio is 6:1) catalyst displayed the best catalytic activity according to the activity evaluation experiments, and chlorobenzene (1000 ppm) was totally decomposed at 270℃. The high activity correlated with a high dispersion of the oxides and was attributed to the exposure of more active sites, which was demonstrated by X-ray diffraction and high-resolution transmission electron microscopy. The strong interactions between MnO₂, Co₃O₄, MnCoO_x, and MCM-41 indicated that cobalt promoted the redox cycles of the manganese system. The bimetal-oxide-based catalyst showed better catalytic activity than that of the single metal oxide catalysts, which was further confirmed by H₂ temperature-programmed reduction. Chlorobenzene temperature-programmed desorption results showed that 10%MnCo(6:1)/MCM-41 had higher adsorption strength for chlorobenzene than that of single metal catalysts. And stronger adsorption was beneficial for combustion of chlorobenzene. Furthermore, 10%MnCo(6:1)/MCM-41 was not deactivated during a continuous reaction for 1000 h at 260℃ and displayed good resistance to water and benzene, which indicated that the catalyst could be used in a wide range of applications.

Key words:

1. [1] L. Zhang, Y. X. Peng, J. Zhang, L. Chen, X. J. Meng, F. S. Xiao, Chin. J. Catal., 2016, 37, 800-809.
2. [2] Y. X. Liu, J. G. Deng, S. H. Xie, Z. W. Wang, H. X. Dai, Chin. J. Catal., 2016, 37, 1193-1205.
3. [3] J. W. Kan, B. Li, L. Li, X. J. Wang, Y. W. Chen, S. M. Zhu, S. B. Shen, Chem. Ind. Eng. Progr., 2016, 35, 499-505.
4. [4] S. F. Zuo, M. L. Ding, J. Tong, L. C. Feng, C. Z. Qi, Appl. Clay Sci., 2015, 105-106, 118-123.
5. [5] V. H. Vu, J. Belkouch, A. Ould-Dris, B. Taouk, J. Hazard. Mater., 2009, 169, 758-765.
6. [6] M. Nikoorazm, F. Ghorbani, A. Ghorbani-Choghamarani, Z. Erfani, Chin. J. Catal., 2017, 38, 1413-1422.
7. [7] Y. Han, F. S. Xiao, Chin. J. Catal., 2003, 24, 149-158.
8. [8] M. H. Yuan, C. C. Chang, C. Y. Chang, W. C. Liao, W. K. Tu, J. Y. Tseng, D. R. Ji, J. L. Shie, Y. H. Chen, J. Taiwan Inst. Chem. Eng., 2015, 53, 52-57.
9. [9] S. Pitkäaho, L. Matejova, S. Ojala, J. Gaalova, R. L. Keiski, Appl. Catal. B, 2012, 113-114, 150-159.
10. [10] Z. E Assal, S. Ojala, S. Pitkäaho, L. Pirault-Roy, B. Darif, J. D. Com-parot, M. Bensitel, R. L. Keiski, R. Brahmi, Chem. Eng. J., 2017, 313, 1010-1022.
11. [11] J. D. Liu, T. T. Zhang, A. P. Jia, M. F. Luo, J. Q. Lu, Appl. Surf. Sci., 2016, 369, 58-66.
12. [12] C. H. Zhang, C. Wang, W. C. Hua, Y. L. Guo, G. Z. Lu, S. Gil, A. Giroir-Fendler, Appl. Catal. B, 2016, 186, 173-183.
13. [13] W. Wang, Q. Zhu, Q. G. Dai, X. Y. Wang, Chem. Eng. J., 2017, 307, 1037-1046.
14. [14] S. Cao, H. Q. Wang, F. X. Yu, M. P. Shi, S. Chen, X. L. Weng, Y. Liu, Z. B. Wu, J. Colloid Interf. Sci., 2016, 463, 233-241.
15. [15] W. Deng, Q. G. Dai, Y. J. Lao, B. B. Shi, X. Y. Wang, Appl. Catal. B, 2016, 181, 848-861.
16. [16] L. Wang, H. K. Xie, X. D. Wang, G. Z. Zhang, Y. L. Guo, Y. Guo, G. Z. Lu, Chin. J. Catal., 2017, 38, 1406-1412.
17. [17] P. Yang, J. R. Li, S. F. Zuo, Chem. Eng. Sci., 2017, 162, 218-226.
18. [18] Y. Yan, L. Wang, H. P. Zhang, X. Y. Zhang, Sep. Purif. Technol., 2017, 175, 213-221.
19. [19] P. Yang, S. S. Yang, Z. N. Shi, Z. H. Meng, R. X. Zhou, Appl. Catal. B, 2015, 162, 227-235.
20. [20] P. Yang, S. F. Zuo, R. X. Zhou, Chem. Eng. J., 2017, 323, 160-170.
21. [21] Q. Q. Huang, Z. H. Meng, R. X. Zhou, Appl. Catal. B, 2012, 115-116, 179-189.
22. [22] Q. Q. Huang, X. M. Xue, R. X. Zhou, J. Mol. Catal. A, 2011, 344, 74-82.
23. [23] P. Yang, X. M. Xue, Z. H. Meng, R. X. Zhou, Chem. Eng. J., 2013, 234, 203-210.
24. [24] Q. Q. Huang, X. M. Xue, R. X. Zhou, J. Hazard. Mater., 2010, 183, 694-700.
25. [25] M. Wu, X. Y. Wang, Q. G. Dai, Y. X. Gu, D. Li, Catal. Today, 2010, 158, 336-342.
26. [26] C. H. Xu, C. Q. Liu, Y. Zhong, X. Z. Yang, J. Y. Liu, Y. C. Yang, Z. X. Ye, Chin. Chem. Lett., 2008, 19, 1387-1390.
27. [27] A. Z. Abdullah, M. Z. Abu Bakar, S. Bhatia, J. Hazard. Mater., 2006, 129, 39-49.
28. [28] D. Li, Y. Zheng, X. Y. Wang, Appl. Catal. A, 2008, 340, 33-41.
29. [29] X. Y. Wang, Q. G. Dai, Y. Zheng, Chin. J. Catal., 2006, 27, 468-470.
30. [30] J. L. Zhao, G. Qian, F. Y. Li, J. Zhu, S. F. Ji, L. Li, Chin. J. Catal., 2012, 33, 771-776.
31. [31] T. A. Konovalova, Y. L. Gao, R. Schad, L. D. Kispert, C. A. Saylor, L. C. Brunel, J. Phys. Chem. B, 2001, 105, 7459-7464.
32. [32] J. R. Li, S. F. Zuo, P. Yang, C. Z. Qi, Mater., 2017, 10, 949.
33. [33] J. W. Kan, L. Deng, B. Li, Q. Huang, S. M. Zhu, S. B. Shen, Y. W. Chen, Appl. Catal. A, 2017, 530, 21-29.
34. [34] M. Wu, X. Y. Wang, Q. G. Dai, D. Li, Catal. Commun., 2010, 11, 1022-1025.
35. [35] M. Wu, X. Y. Wang, Q. G. Dai, Y. X. Gu, D. Li, Catal. Today, 2010, 158, 336-342.
36. [36] S. F. Zuo, P. Yang, X. Q. Wang, ACS Omega, 2017, 2, 5179-5186.
37. [37] W. Zhao, J. Cheng, L. N. Wang, J. L. Chu, J. K. Qu, Y. H. Liu, S. H. Li, H. Zhang, J. C. Wang, Z. P. Hao, T. Qi, Appl. Catal. B, 2012, 127, 246-254.
38. [38] G. L. Zhou, X. L. He, S. Liu, H. M. Xie, M. Fu, J. Ind. Eng. Chem., 2015, 21, 932-941.
39. [39] T. Cai, H. Huang, W. Deng, Q. G. Dai, W. Liu, X. Y. Wang, Appl. Catal. B, 2015, 166-167, 393-405.
40. [40] G. L. Zhou, X. L. He, S. Liu, H. M. Xie, M. Fu, J. Ind. Eng. Chem., 2014, 5, 21, 932-941.
41. [41] D. A. Aguilera, A. Perez, R. Molina, S. Moreno, Appl. Catal. B, 2011, 104, 144-150.

扫一扫看文章

计量

PDF下载量: 0
文章访问数: 817
HTML全文浏览量: 52

通讯作者: 陈斌, bchen63@163.com

1.
沈阳化工大学材料科学与工程学院沈阳 110142

MnCo改性的MCM-41催化剂用于氯苯催化燃烧的研究

English

Preparation of MnCo/MCM-41 catalysts with high performance for chlorobenzene combustion

CCS Chemistry：嵌段共聚物自组装成 “三明治”二维有机材料，实现纳米级压力传感功能

CCS Chemistry：颜徐州、鲍哲南：你的皮肤可能是一片SPMs

CCS Chemistry：工作高效不疲劳，只须让催化剂动起来

CCS Chemistry：静电组装导向聚合- 聚电解质纳米凝胶量化制备新策略

CCS Chemistry：金黄色葡萄球菌醛基脱氢酶是如何识别特异性底物的？

计量

通讯作者: 陈斌, bchen63@163.com

中国化学会秘书处

MnCo改性的MCM-41催化剂用于氯苯催化燃烧的研究

English

Preparation of MnCo/MCM-41 catalysts with high performance for chlorobenzene combustion

CCS Chemistry：嵌段共聚物自组装成 “三明治”二维有机材料，实现纳米级压力传感功能

CCS Chemistry：颜徐州、鲍哲南： 你的皮肤可能是一片SPMs

CCS Chemistry：工作高效不疲劳，只须让催化剂动起来

CCS Chemistry：静电组装导向聚合- 聚电解质纳米凝胶量化制备新策略

CCS Chemistry：金黄色葡萄球菌醛基脱氢酶是如何识别特异性底物的？

计量

文章相关

通讯作者: 陈斌, bchen63@163.com

中国化学会秘书处

CCS Chemistry：颜徐州、鲍哲南：你的皮肤可能是一片SPMs