以Ca-M-Al(M=Mg,La,Ce,Y)层状双氢氧化物为前驱体的固体碱用于酯交换合成碳酸二甲酯

引用本文: 廖云辉, 李枫, 代鑫, 赵宁, 肖褔魁. 以Ca-M-Al(M=Mg,La,Ce,Y)层状双氢氧化物为前驱体的固体碱用于酯交换合成碳酸二甲酯[J]. 催化学报, 2017, 38(11): 1860-1869. doi: 10.1016/S1872-2067(17)62898-5 shu

Citation: Yunhui Liao, Feng Li, Xin Dai, Ning Zhao, Fukui Xiao. Solid base catalysts derived from Ca-M-Al (M=Mg, La, Ce, Y) layered double hydroxides for dimethyl carbonate synthesis by transesterification of methanol with propylene carbonate[J]. Chinese Journal of Catalysis, 2017, 38(11): 1860-1869. doi: 10.1016/S1872-2067(17)62898-5 shu

以Ca-M-Al(M=Mg,La,Ce,Y)层状双氢氧化物为前驱体的固体碱用于酯交换合成碳酸二甲酯

a 中国科学院山西煤炭化学研究所煤转化国家重点实验室, 山西太原 030001;
b 中国科学院大学, 北京 100049;
c 国家煤基合成工程技术研究中心, 山西太原 030001
基金项目:
山西省自然科学基金（201601D102006）；山西省煤基重点科技攻关项目（MD2014-09，MD2014-10）.

摘要: 碳酸二甲酯（DMC）是一种环境友好型绿色化学品，可作为甲基化和羰基化试剂用于取代传统剧毒的硫酸二甲酯和光气.另外，DMC具有良好的溶解性能，可用于高级溶剂；DMC分子中具有高的氧含量，可用作汽油添加剂来提高汽油的辛烷值；DMC还可用作聚碳酸酯的原料.随着人们环保意识的不断增强，DMC的生产和应用呈现出巨大的吸引力和市场潜力.DMC合成方法主要有光气法、甲醇氧化羰化法、尿素醇解法及酯交换法等.酯交换法具有反应条件温和、产率高等优点，是目前工业制备DMC的主要方法.研究发现，相对于酸性催化剂，碱性催化剂更有利于酯交换法合成DMC.金属氧化物催化剂具有活性高、热稳定性高及可连续重复回收利用等优点，因而引起了广泛关注.CaO对于酯交换合成DMC反应具有良好的催化活性，但其稳定性差.因此，通常采用复合金属氧化物来促进CaO的分散，并增加金属间相互作用以防止CaO流失.研究发现，经煅烧后的Mg-Al，Ca-Al和Ca-Mg-Al催化剂对于酯交换反应具有高的活性和稳定性.此外，通过碱性稀土金属（La，Ce和Y）的引入可以修饰催化剂上的碱性位点，从而调变催化剂的碱性.
本文合成了一系列以Ca-M-Al （M=Mg，La，Ce，Y）层状双氢氧化物为前驱体的固体碱催化剂，将其用于甲醇与碳酸丙烯酯酯交换合成DMC.通过X射线衍射、热重分析、红外光谱、X射线光电子能谱、电感耦合等离子体、CO₂程序升温脱附和Hammett指示剂对催化剂进行了表征.研究发现，各催化剂的活性高低依次为：Ca-Y-Al < Ca-Al < Ca-Ce-Al < Ca-La-Al < Ca-Mg-Al，这与催化剂表面总碱量相一致.通过Mg和La的引入，催化剂表面出现了超强碱性位.其中，Ca-Mg-Al催化剂表面具有最高的（Ca+Mg）：Al原子比，从而导致催化剂表面产生更多的不饱和O^2-离子，因而具有最高的碱性位数量.此外，通过Mg，La，Ce和Y的引入，催化剂的重复使用性能得到了提高.特别是Ca-Mg-Al催化剂，在10次循环后仍保持着高的活性，且其结构没有发生显著变化，表明其稳定性较高，因此该催化剂在非均相催化中具有高的应用价值.

关键词:

English

Solid base catalysts derived from Ca-M-Al (M=Mg, La, Ce, Y) layered double hydroxides for dimethyl carbonate synthesis by transesterification of methanol with propylene carbonate

a State Key Laboratory of Coal Conversion, Institute of Coal Chemistry, Chinese Academy of Sciences, Taiyuan 030001, Shanxi, China;
b University of Chinese Academy of Sciences, Beijing 100049, Shanxi, China;
c National Engineering Research Center for Coal-Based Synthesis, Taiyuan 030001, Shanxi, China
Received Date: 11 July 2017
Revised Date: 15 August 2017
Fund Project:
This work was supported by the Natural Science Foundation of Shanxi Province (201601D102006) and the Key Science and Technology Program of Shanxi Province, China (MD2014-09, MD2014-10).

Abstract: Composite solid base catalysts derived from Ca-M-Al (M=Mg, La, Ce, Y) layered double hydroxides (LDH) were synthesized, characterized and applied to the transesterification of methanol with pro-pylene carbonate. X-ray diffraction analyses of the catalysts show that all of the catalysts were in the form of composite oxides. Compared with the Ca-Al LDH catalyst, the specific surface areas and pore volumes of the catalysts were increased with the introduction of Mg, La or Ce. The catalytic perfor-mance of these catalysts increases in the order of Ca-Y-Al < Ca-Al < Ca-Ce-Al < Ca-La-Al < Ca-Mg-Al, which is consistent with the total surface basic amounts of these materials and the formation of especially strong basic sites following modification with Mg and La. The Ca-Mg-Al catalyst shows the highest (Ca+Mg):Al atomic ratio, indicating that it likely contains more unsaturated O^2- ions, providing it with the highest concentration of very strong basic sites. The recyclability of these cat-alysts is improved following the addition of Mg, La, Ce or Y, with the Ca-Mg-Al maintaining a high level of activity after ten recycling trials. X-ray diffraction analyses of fresh and used Ca-Mg-Al demonstrate that this catalyst is exceptionally stable, which could be of value in practical applica-tions related to heterogeneous catalysis.

Key words:

1. [1] Y. Ono, Appl. Catal. A, 1997, 155, 133-166.
2. [2] D. F. Wang, X. L. Zhang, J. Ma, H. W. Yu, J. Z. Shen, W. Wei, Catal. Sci. Technol., 2016, 6, 1530-1545.
3. [3] D. D. Wu, Z. Chen, Ind. Eng. Chem. Res., 2009, 48, 6287-6290.
4. [4] S. Y. Huang, B. Yan, S. P. Wang, X. B. Ma, Chem. Soc. Rev., 2015, 44, 3079-3116.
5. [5] G. Merza, B. László, A. Oszkó, G. Pótári, E. Varga, A. Erdőhelyi, Catal. Lett., 2014, 145, 881-892.
6. [6] R. G. Zhang, J. R. Li, B. J. Wang, RSC Adv., 2013, 3, 12287-12298.
7. [7] J. Q. Wang, J. Sun, W. G. Cheng, C. Y. Shi, K. Dong, X. P. Zhang, S. J. Zhang, Catal. Sci. Technol., 2012, 2, 600-605.
8. [8] A. Pyrlik, W. F. Hoelderich, K. Müller, W. Arlt, J. Strautmann, D. Kruse, Appl. Catal. B, 2012, 125, 486-491.
9. [9] H. Wang, M. H. Wang, S. G. Liu, N. Zhao, W. Wei, Y. H. Sun, J. Mol. Catal. A, 2006, 258, 308-312.
10. [10] P. Kumar, V. C. Srivastava, I. M. Mishra, Energy Fuels, 2015, 29, 2664-2675.
11. [11] C. C. Wu, X. Q. Zhao, Y. J. Wang, Catal. Commun., 2005, 6, 694-698.
12. [12] X. M. Wu, M. Kang, N. Zhao, W. Wei, Y. H. Sun, Catal. Commun., 2014, 46, 46-50.
13. [13] C. Zhang, B. Lu, X. G. Wang, J. X. Zhao, Q. H. Cai, Catal. Sci. Technol., 2012, 2, 305-309.
14. [14] J. Bian, M. Xiao, S. J. Wang, X. J. Wang, Y. X. Lu, Y. Z. Meng, Chem. Eng. J., 2009, 147, 287-296.
15. [15] A. Bansode, A. Urakawa, ACS Catal., 2014, 4, 3877-3880.
16. [16] X. L. Wu, Y. Z. Meng, M. Xiao, Y. X. Lu, J. Mol. Catal. A, 2006, 249, 93-97.
17. [17] R. Srivastava, D. Srinivas, P. Ratnasamy, J. Catal., 2006, 241, 34-44.
18. [18] J. Xu, H. T. Wu, C. M. Ma, B. Xue, Y. X. Li, Y. Cao, Appl. Catal. A, 2013, 464-465, 357-363.
19. [19] C. Murugan, H. C. Bajaj, R. V. Jasra, Catal. Lett., 2010, 137, 224-231.
20. [20] R. Juárez, A. Corma, H. García, Green Chem., 2009, 11, 949-952.
21. [21] P. Kumar, V. C. Srivastava, I. M. Mishra, Catal. Commun., 2015, 60, 27-31.
22. [22] H. Wang, M. H. Wang, N. Zhao, W. Wei, Y. H. Sun, Catal. Lett., 2005, 105, 253-257.
23. [23] K. Yan, A. C. Chen, Fuel, 2014, 115, 101-108.
24. [24] T. Wei, M. H. Wang, W. Wei, Y. H. Sun, B. Zhong, Green Chem., 2003, 5, 343-346.
25. [25] K. Yan, G. S. Wu, W. Jin, Energy Technol., 2016, 4, 354-368.
26. [26] K. Yan, Y. Q. Liu, Y. R. Lu, J. J. Chai, L. P. Sun, Catal. Sci. Technol., 2017, 7, 1622-1645.
27. [27] K. Takehira, Appl. Clay Sci., 2017, 136, 112-141.
28. [28] H. S. Ji, W. H. Wu, F. H. Li, X. X. Yu, J. J. Fu, L. Y. Jia, J. Hazard. Mater., 2017, 334, 212-222.
29. [29] N. B. Allou, P. Saikia, A. Borah, R. L. Goswamee, Colloid Polym. Sci., 2017, 295, 725-747.
30. [30] Y. Lu, B. Jiang, L. Fang, F. L. Ling, F. Wu, B. S. Hu, F. M. Meng, K. Y. Niu, F. Lin, H. M. Zheng, J. Alloys Compd., 2017, 714, 63-70.
31. [31] L. P. Zheng, S. X. Xia, X. Y. Lu, Z. Y. Hou, Chin. J. Catal., 2015, 36, 1759-1765.
32. [32] L. P. Zheng, S. X. Xia, Z. T. Hou, M. Y. Zhang, Z. Y. Hou, Chin. J. Catal., 2014, 35, 310-318.
33. [33] L. J. Gao, G. Y. Teng, J. H. Lv, G. M. Xiao, Energy Fuels, 2010, 24, 646-651.
34. [34] C. S. Castro, L. C. F. Garcia, J. M. Assaf, Fuel Process. Technol., 2014, 125, 73-78.
35. [35] Z. Wang, P. Fongarland, G. Z. Lu, N. Essayem, J. Catal., 2014, 318, 108-118.
36. [36] J. Kocík, M. Hájek, I. Troppová, Fuel Process. Technol., 2015, 134, 297-302.
37. [37] F. Cavani, F. Trifirb, A. Vaccari, Catal. Today, 1991, 11, 173-301.
38. [38] F. Li, Y. F. Wang, Q. Z. Yang, D. G. Evans, C. Forano, X. Duan, J. Hazard. Mater., 2005, 125, 89-95.
39. [39] A. C. Vieira, R. L. Moreira, A. Dias, J. Phys. Chem. C, 2009, 113, 13358-13368.
40. [40] B. Yu, H. Bian, J. Plank, J. Phys. Chem. Solids, 2010, 71, 468-472.
41. [41] S. S. Peng, M. H. Yang, W. K. Zhang, X. N. Li, C. Wang, M. B. Yue, Microporous Mesoporous Mater., 2017, 242, 18-24.
42. [42] J. Li, D. Wang, G. D. Zhou, Y. X. Xue, C. Li, T. X. Cheng, Ind. Eng. Chem. Res., 2011, 50, 10955-10961.
43. [43] X. Chen, Y. Liu, G. Niu, Z. Yang, M. Bian, A. He, Appl. Catal. A, 2001, 205, 159-172.
44. [44] L. P. Haack, J. E. DeVries, K. Otto, M. S. Chattha, Appl. Catal. A, 1992, 82, 199-214.
45. [45] J. S. Ledford, M. Houalla, A. Proctor, D. M. Hercules, L. Petrakis, J. Chem. Phys., 1989, 93, 6770-6777.
46. [46] A. F. Lucrédio, G. Tremiliosi Filho, E. M. Assaf, Appl. Surf. Sci., 2009, 255, 5851-5856.
47. [47] T. Gougousi, Z. Y. Chen, Thin Solid Films, 2008, 516, 6197-6204.
48. [48] S. A. Barve, Jagannath, M. N. Deo, R. Kishore, A. Biswas, L. M. Gantayet, D. S. Patil, Appl. Surf. Sci., 2010, 257, 215-221.
49. [49] Y. Uwamino, T. Ishizuka, H. Yamatera, J. Electron. Spectrosc. Relat. Phenom., 1984, 34, 67-78.
50. [50] J. Y. Wang, L. M. Yang, W. Luo, G. X. Yang, C. L. Miao, J. Y. Fu, S. Y. Xing, P. Fan, P. M. Lv, Z. M. Wang, Fuel, 2017, 196, 306-313.
51. [51] L. L. Marciniuk, P. Hammer, H. O. Pastore, U. Schuchardt, D. Cardoso, Fuel, 2014, 118, 48-54.
52. [52] J. Campbell, Int. Mater. Rev., 1994, 39, 125-125.
53. [53] G. Busca, Chem. Rev., 2010, 110, 2217-2249.
54. [54] H. Gorzawski, W. F. Hoelderich, J. Mol. Catal. A, 1999, 144, 181-187.
55. [55] G. D. Wu, X. L. Wang, W. Wei, Y. H. Sun, Appl. Catal. A, 2010, 377, 107-113.
56. [56] P. Kumar, V. C. Srivastava, I. M. Mishra, Catal. Commun., 2015, 60, 27-31.
57. [57] M. K. Lam, K. T. Lee, A. R. Mohamed, Appl. Catal. B, 2009, 93, 134-139.
58. [58] G. D. Wu, X. L. Wang, W. Wei, Y. H. Sun, Appl. Catal. A, 2010, 377, 107-113.
59. [59] T. Wei, M. H. Wang, W. Wei, Y. H. Sun, B. Zhong, Fuel Process. Technol., 2003, 83, 175-182.

扫一扫看文章

计量

PDF下载量: 8
文章访问数: 824
HTML全文浏览量: 54

通讯作者: 陈斌, bchen63@163.com

1.
沈阳化工大学材料科学与工程学院沈阳 110142

以Ca-M-Al(M=Mg,La,Ce,Y)层状双氢氧化物为前驱体的固体碱用于酯交换合成碳酸二甲酯

English

Solid base catalysts derived from Ca-M-Al (M=Mg, La, Ce, Y) layered double hydroxides for dimethyl carbonate synthesis by transesterification of methanol with propylene carbonate

CCS Chemistry：嵌段共聚物自组装成 “三明治”二维有机材料，实现纳米级压力传感功能

CCS Chemistry：颜徐州、鲍哲南：你的皮肤可能是一片SPMs

CCS Chemistry：工作高效不疲劳，只须让催化剂动起来

CCS Chemistry：静电组装导向聚合- 聚电解质纳米凝胶量化制备新策略

CCS Chemistry：金黄色葡萄球菌醛基脱氢酶是如何识别特异性底物的？

计量

通讯作者: 陈斌, bchen63@163.com

中国化学会秘书处

以Ca-M-Al(M=Mg,La,Ce,Y)层状双氢氧化物为前驱体的固体碱用于酯交换合成碳酸二甲酯

English

Solid base catalysts derived from Ca-M-Al (M=Mg, La, Ce, Y) layered double hydroxides for dimethyl carbonate synthesis by transesterification of methanol with propylene carbonate

CCS Chemistry：嵌段共聚物自组装成 “三明治”二维有机材料，实现纳米级压力传感功能

CCS Chemistry：颜徐州、鲍哲南： 你的皮肤可能是一片SPMs

CCS Chemistry：工作高效不疲劳，只须让催化剂动起来

CCS Chemistry：静电组装导向聚合- 聚电解质纳米凝胶量化制备新策略

CCS Chemistry：金黄色葡萄球菌醛基脱氢酶是如何识别特异性底物的？

计量

文章相关

通讯作者: 陈斌, bchen63@163.com

中国化学会秘书处

CCS Chemistry：颜徐州、鲍哲南：你的皮肤可能是一片SPMs