Citation: Huanmin Li, Xianwei Sui, Xu-Ming Xie. Correlation of Morphology Evolution with Superior Mechanical Properties in PA6/PS/PP/SEBS Blends Compatibilized by Multi-phase Compatibilizers[J]. Chinese Journal of Polymer Science, ;2018, 36(7): 848-858. doi: 10.1007/s10118-018-2102-2 shu

Correlation of Morphology Evolution with Superior Mechanical Properties in PA6/PS/PP/SEBS Blends Compatibilized by Multi-phase Compatibilizers

Laboratory of Advanced Materials (Ministry of Education), Department of Chemical Engineering, Tsinghua University, Beijing 100084, China

Corresponding author: Xu-Ming Xie, xxm-dce@mail.tsinghua.edu.cn
Received Date: 13 September 2017
Revised Date: 11 December 2017
Accepted Date: 11 December 2017
Available Online: 13 July 2018

In this study, the maleic anhydride (MAH) and styrene (St) dual monomers grafted polypropylene (PP) and poly[styrene-b-(ethylene-co-butylene)-b-styrene] (SEBS), i.e. PP-g-(MAH-co-St) and SEBS-g-(MAH-co-St) are prepared as multi-phase compatibilizers and used to compatibilize the PA6/PS/PP/SEBS (70/10/10/10) model quaternary blends. Both PS and SEBS are encapsulated by the hard shell of PP-g-(MAH-co-St) in the dispersed domains (about 2 μm) of the PA6/PS/PP-g-(MAH-co-St)/SEBS (70/10/10/10) quaternary blend. In contrast, inside the dispersed domains (about 1 μm) of the PA6/PS/PP/SEBS-g-(MAH-co-St) (70/10/10/10) quaternary blend, the soft SEBS-g-(MAH-co-St) encapsulates both the hard PS and PP phases and separates them. With increasing the content of the compatibilizers equally, the morphology of the PA6/PS/(PP+PP-g-(MAH-co-St))/(SEBS+SEBS-g-(MAH-co-St)) (70/10/10/10) quaternary blends evolves from the soft (SEBS+SEBS-g-(MAH-co-St)) encapsulating PS and partially encapsulating PP (about 1 μm), then to PS exclusively encapsulated by the soft SEBS-g-(MAH-co-St) and then separated by PP-g-(MAH-co-St) inside the smaller domains (about 0.6 μm). This morphology evolution has been well predicted by spreading coefficients and explained by the reaction between the matrix PA6 and the compatibilizers. The quaternary blends compatibilized by more compatibilizers exhibit stronger hierarchical interfacial adhesions and smaller dispersed domain, which results in the further improved mechanical properties. Compared to the uncompatibilized blend, the blend with both 10 wt% PP-g-(MAH-co-St) and 10 wt% SEBS-g-(MAH-co-St) has the best mechanical properties with the stress at break, strain at break and impact failure energy improved significantly by 97%, 71% and 261%, respectively. There is a strong correlation between the structure and property in the blends.
- Compatibilization,
- Morphology evolution,
- Superior mechanical properties
1. [1]
  Koning, C.; van Duin, M.; Pagnoulle, C.; Jerome, R. Strategies for compatibilization of polymer blends. Prog. Polym. Sci. 1998, 23(4), 707-757. doi: 10.1016/S0079-6700(97)00054-3
2. [2]
  Paul, D. R.; Bucknall, C. B. "Polymer blends", Wiley, New York, 2000.
3. [3]
  Robeson, L. M. "Polymer blends: a comprehensive review", Carl Hanser Verlag, 2007.
4. [4]
  Adedeji, A.; Lyu, S.; Macosko, C. W. Block copolymers in homopolymer blends: interface vs micelles. Macromolecules 2001, 34(25), 8663-8668. doi: 10.1021/ma001944b
5. [5]
  Marić, M.; Macosko, C. W. Block copolymer compatibilizers for polystyrene/poly(dimethylsiloxane) blends. J. Polym. Sci., Part B: Polym. Phys. 2002, 40(4), 346-357. doi: 10.1002/(ISSN)1099-0488
6. [6]
  Harrats, C.; Fayt, R.; Jérôme, R.; Blacher, S. Stabilization of a cocontinuous phase morphology by a tapered diblock or triblock copolymer in polystyrene-rich low-density polyethylene/polystyrene blends. J. Polym. Sci., Part B: Polym. Phys. 2003, 41(2), 202-216. doi: 10.1002/polb.10370
7. [7]
  Guo, R. H.; Li, J. L.; Yan, L. T.; Xie, X. M. Role of compatibilizer in multicomponent polymer mixtures under shear flow. Soft Matter 2013, 9(1), 255-260. doi: 10.1039/C2SM26342D
8. [8]
  Bhadane, P. A.; Tsou, A. H.; Cheng, J.; Ellul, M. D.; Favis, B. D. Enhancement in interfacial reactive compatibilization by chain mobility. Polymer 2014, 55(16), 3905-3914. doi: 10.1016/j.polymer.2014.05.023
9. [9]
  Gao, C.; Zhang, S.; Li, X.; Zhu, S.; Jiang, Z. Synthesis of poly(ether ether ketone)-block-polyimide copolymer and its compatibilization for poly(ether ether ketone)/thermoplastic polyimide blends. Polymer 2014, 55(1), 119-125. doi: 10.1016/j.polymer.2013.11.022
10. [10]
  Xu, Y.; Thurber, C. M.; Macosko, C. W.; Lodge, T.P.; Hillmyer, M.A. Poly(methyl methacrylate)-block-polyethylene-block-poly(methyl methacrylate) triblock copolymers as compatibilizers for polyethylene/poly(methyl methacrylate) blends. Ind. Eng. Chem. Res. 2014, 53(12), 4718-4725. doi: 10.1021/ie4043196
11. [11]
  Parpaite, T.; Otazaghine, B.; Caro, A. S.; Taguet, A.; Sonnier, R.; Lopez-Cuesta, J. M. Janus hybrid silica/polymer nanoparticles as effective compatibilizing agents for polystyrene/polyamide-6 melted blends. Polymer 2016, 90, 34-44. doi: 10.1016/j.polymer.2016.02.044
12. [12]
  Koriyama, H.; Oyama, H. T.; Ougizawa, T.; Inoue, T.; Weber, M.; Koch, E. Studies on the reactive polysulfone-polyamide interface: interfacial thickness and adhesion. Polymer 1999, 40(23), 6381-6393. doi: 10.1016/S0032-3861(98)00856-8
13. [13]
  Zhang, J.; Lodge, T. P.; Macosko, C. W. Interfacial morphology development during PS/PMMA reactive coupling. Macromolecules 2005, 38(15), 6586-6591. doi: 10.1021/ma050530l
14. [14]
  Harada, M.; Iida, K.; Okamoto, K.; Hayashi, H.; Hirano, K. Reactive compatibilization of biodegradable poly(lactic acid)/poly(ε-caprolactone) blends with reactive processing agents. Polym. Eng. Sci. 2008, 48(7), 1359-1368. doi: 10.1002/(ISSN)1548-2634
15. [15]
  Liu, G. C.; He, Y. S.; Zeng, J. B.; Li, Q. T.; Wang, Y. Z. Fully biobased and supertough polylactide-based thermoplastic vulcanizates fabricated by peroxide-induced dynamic vulcanization and interfacial compatibilization. Biomacromolecules, 2014, 15(11), 4260-4271. doi: 10.1021/bm5012739
16. [16]
  Li, X.; Kang, H.; Shen, J.; Zhang, L.; Nishi, T.; Ito, K.; Zhao, C.; Coates, P. Highly toughened polylactide with novel sliding graft copolymer by in situ reactive compatibilization, crosslinking and chain extension. Polymer 2014, 55(16), 4313-4323. doi: 10.1016/j.polymer.2014.06.045
17. [17]
  Wang, H.; Dong, W.; Li, Y. Compatibilization of immiscible polymer blends using in situ formed janus nanomicelles by reactive blending. ACS Macro Lett. 2015, 4(12), 1398-1403. doi: 10.1021/acsmacrolett.5b00763
18. [18]
  Thurber, C. M.; Xu, Y.; Myers, J. C.; Lodge, T. P.; Macosko, C. W. Accelerating reactive compatibilization of PE/PLA blends by an interfacially localized catalyst. ACS Macro Lett. 2015, 4(1), 30-33. doi: 10.1021/mz500770y
19. [19]
  Ojijo, V.; Ray, S. S. Super toughened biodegradable polylactide blends with non-linear copolymer interfacial architecture obtained via facile in-situ reactive compatibilization. Polymer 2015, 80, 1-17. doi: 10.1016/j.polymer.2015.10.038
20. [20]
  Todd, A. D.; McEneany, R. J.; Topolkaraev, V. A.; Macosko, C. W.; Hillmyer, M. A. Reactive compatibilization of poly(ethylene terephthalate) and high-density polyethylene using amino-telechelic polyethylene. Macromolecules 2016, 49(23), 8988-8994. doi: 10.1021/acs.macromol.6b02080
21. [21]
  Li, J. P.; Cassagnau, P.; Da Cruz-Boisson, F.; Mélis, F.; Alcouffe, P.; Bounor-Legaré, V. Efficient hydrosilylation reaction in polymer blending: an original approach to structure PA12/PDMS blends at multiscales. Polymer 2017, 112, 10-25. doi: 10.1016/j.polymer.2017.01.039
22. [22]
  Zolali, A. M.; Favis, B. D. Compatibilization and toughening of co-continuous ternary blends via partially wet droplets at the interface. Polymer 2017, 114, 277-288. doi: 10.1016/j.polymer.2017.02.093
23. [23]
  Dang, L.; Nai, X. Y.; Liu, X.; Zhu, D. H.; Dong, Y. P.; Li, W. Effects of different compatibilizing agents on the interfacial adhesion properties of polypropylene/magnesium oxysulfate whisker composites. Chinese J. Polym. Sci. 2017, 35(9), 1143-1155. doi: 10.1007/s10118-017-1953-2
24. [24]
  Chanda, M.; Roy, S. K. "Plastics fabrication and recycling", Taylor and Francis, 2009.
25. [25]
  Xanthos, M. Recycling of the #5 Polymer. Science 2012, 337(6095), 700-702. doi: 10.1126/science.1221806
26. [26]
  Eagan, J. M.; Xu, J.; Di Girolamo, R.; Thurber, C. M.; Macosko, C. W.; LaPointe, A. M.; Bates, F. S.; Coates, G. W. Combining polyethylene and polypropylene: Enhanced performance with PE/iPP multiblock polymers. Science 2017, 355(6327), 814-816. doi: 10.1126/science.aah5744
27. [27]
  Debolt, M. A.; Robertson, R. E. Impact strength and elongation-to-break of compatibilized ternary blends of polypropylene, nylon 66, and polystyrene. Polym. Eng. Sci. 2004, 44(9), 1800-1809. doi: 10.1002/(ISSN)1548-2634
28. [28]
  DeBolt, M. A.; Robertson, R. E. Morphology of compatibilized ternary blends of polypropylene, nylon 66, and polystyrene. Polym. Eng. Sci. 2006, 46(4), 385-398. doi: 10.1002/(ISSN)1548-2634
29. [29]
  Omonov, T. S.; Harrats, C.; Groeninckx, G. Co-continuous and encapsulated three phase morphologies in uncompatibilized and reactively compatibilized polyamide 6/polypropylene/polystyrene ternary blends using two reactive precursors. Polymer 2005, 46(26), 12322-12336. doi: 10.1016/j.polymer.2005.10.022
30. [30]
  Guo, H. F.; Gvozdic, N. V.; Meier, D. J. Prediction and manipulation of the phase morphologies of multiphase polymer blends: II. quaternary systems. Polymer 1997, 38(19), 4915-4923.
31. [31]
  Virgilio, N.; Desjardins, P.; L’Espérance, G.; Favis, B. D. In situ measure of interfacial tensions in ternary and quaternary immiscible polymer blends demonstrating partial wetting. Macromolecules 2009, 42(19), 7518-7529. doi: 10.1021/ma9005507
32. [32]
  Virgilio, N.; Favis, B. D. Self-assembly of Janus composite droplets at the interface in quaternary immiscible polymer blends. Macromolecules 2011, 44(15), 5850-5856. doi: 10.1021/ma200647t
33. [33]
  Virgilio, N.; Sarazin, P.; Favis, B. D. Towards ultraporous poly(L-lactide) scaffolds from quaternary immiscible polymer blends. Biomaterials 2010, 31(22), 5719-5728. doi: 10.1016/j.biomaterials.2010.03.071
34. [34]
  Ravati, S.; Favis, B. D. Low percolation threshold conductive device derived from a five-component polymer blend. Polymer 2010, 51(16), 3669-3684. doi: 10.1016/j.polymer.2010.06.015
35. [35]
  Wang, J.; Reyna-Valencia, A.; Chaigneau, R.; Favis, B. D. Controlling the hierarchical structuring of conductive PEBA in ternary and quaternary blends. Ind. Eng. Chem. Res. 2016, 55(50), 12848-12859. doi: 10.1021/acs.iecr.6b03700
36. [36]
  Wang, D.; Xie, X. M. Novel strategy for ternary polymer blend compatibilization. Polymer 2006, 47(23), 7859-7863. doi: 10.1016/j.polymer.2006.09.026
37. [37]
  Wang, D.; Li, Y.; Xie, X. M.; Guo, B. H. Compatibilization and morphology development of immiscible ternary polymer blends. Polymer 2011, 52(1), 191-200. doi: 10.1016/j.polymer.2010.11.019
38. [38]
  Li, Y.; Wang, D.; Zhang, J. M.; Xie, X. M. Compatibilization and toughening of immiscible ternary blends of polyamide 6, polypropylene (or a propylene-ethylene copolymer), and polystyrene. J. Appl. Polym. Sci. 2011, 119(3), 1652-1658. doi: 10.1002/app.v119:3
39. [39]
  Li, H.; Xie, X. M. Morphology development and superior mechanical properties of PP/PA6/SEBS ternary blends compatibilized by using a highly efficient multi-phase compatibilizer. Polymer 2017, 108, 1-10. doi: 10.1016/j.polymer.2016.11.044
40. [40]
  Li, H.; Sui, X.; Xie, X. M. High-strength and super-tough PA6/PS/PP/SEBS quaternary blends compatibilized by using a highly effective multi-phase compatibilizer: toward efficient recycling of waste plastics. Polymer 2017, 123, 240-246. doi: 10.1016/j.polymer.2017.07.024
41. [41]
  Li, Y.; Xie, X. M. Studies on mechanism of free radical melt-grafting of multi-monomer system for maleic anhydride/styrene onto polypropylene. Chem. J. Chinese U. 2000, 21(4), 637-642.
42. [42]
  Xie, X. M.; Chen, N. H.; Guo, B. H.; Li, S. Study of multi-monomer melt-grafting onto polypropylene in an extruder. Polym. Int. 2000, 49(12), 1677-1683. doi: 10.1002/(ISSN)1097-0126
43. [43]
  Li, Y.; Xie, X. M.; Guo, B. H. Study on styrene-assisted melt free-radical grafting of maleic anhydride onto polypropylene. Polymer 2001, 42(8), 3419-3425. doi: 10.1016/S0032-3861(00)00767-9
44. [44]
  Xie, X.; Li, Y.; Zhang, J.; Yang, X. Study of melt free radical grafting of maleic anhydride and styrene onto polypropylene and its properties. Acta Polymerica Sinica (in Chinese) 2002, 1, 7-12.
45. [45]
  Hobbs, S. Y.; Dekkers, M. E. J.; Watkins, V. H. Effect of interfacial forces on polymer blend morphologies. Polymer 1988, 29(9), 1598-1602. doi: 10.1016/0032-3861(88)90269-8
46. [46]
  Wu, S. "Polymer interface and adhesion", Marcel Dekker, New York, 1982.
1. [1]
  Dongmei Yao , Junsheng Zheng , Liming Jin , Xiaomin Meng , Zize Zhan , Runlin Fan , Cong Feng , Pingwen Ming . Effect of surface oxidation on the interfacial and mechanical properties in graphite/epoxy composites composite bipolar plates. Chinese Chemical Letters, 2024, 35(11): 109382-. doi: 10.1016/j.cclet.2023.109382
2. [2]
  Zhihao Gu , Jiabo Le , Hehe Wei , Zehui Sun , Mahmoud Elsayed Hafez , Wei Ma . Unveiling the intrinsic properties of single NiZnFeO_x entity for promoting electrocatalytic oxygen evolution. Chinese Chemical Letters, 2024, 35(4): 108849-. doi: 10.1016/j.cclet.2023.108849
3. [3]
  Zhongjie Li , Xiangyue Kong , Yuhao Liu , Huayu Qiu , Lingling Zhan , Shouchun Yin . Progress of additives for morphology control in organic photovoltaics. Chinese Chemical Letters, 2024, 35(6): 109378-. doi: 10.1016/j.cclet.2023.109378
4. [4]
  Kai Han , Guohui Dong , Ishaaq Saeed , Tingting Dong , Chenyang Xiao . Morphology and photocatalytic tetracycline degradation of g-C3N4 optimized by the coal gangue. Chinese Journal of Structural Chemistry, 2024, 43(2): 100208-100208. doi: 10.1016/j.cjsc.2023.100208
5. [5]
  Xin Lu , Haoran Sun , Xiaomeng Li , Chunrui Li , Jinfeng Wang , Dandan Zhou . C14-HSL limits the mycelial morphology of pathogen Trichosporon cells but enhances their aggregation: Mechanisms and implications. Chinese Chemical Letters, 2024, 35(6): 108936-. doi: 10.1016/j.cclet.2023.108936
6. [6]
  Pei Cao , Yilan Wang , Lejian Yu , Miao Wang , Liming Zhao , Xu Hou . Dynamic asymmetric mechanical responsive carbon nanotube fiber for ionic logic gate. Chinese Chemical Letters, 2024, 35(6): 109421-. doi: 10.1016/j.cclet.2023.109421
7. [7]
  Xingqun Pu , Rongrong Liu , Yuting Xie , Chenjing Yang , Jingyi Chen , Baoling Guo , Chun-Xia Zhao , Peng Zhao , Jian Ruan , Fangfu Ye , David A Weitz , Dong Chen . One-step preparation of biocompatible amphiphilic dimer nanoparticles with tunable particle morphology and surface property for interface stabilization and drug delivery. Chinese Chemical Letters, 2025, 36(3): 109820-. doi: 10.1016/j.cclet.2024.109820
8. [8]
  Shan Jiang , Lingchen Meng , Wenyue Ma , Qingkai Qi , Wei Zhang , Bin Xu , Leijing Liu , Wenjing Tian . Corrigendum to 'Morphology controllable conjugated network polymers based on AIE-active building block for TNP detection' [Chin. Chem. Lett. 32 (2021) 1037-1040]. Chinese Chemical Letters, 2024, 35(12): 108998-. doi: 10.1016/j.cclet.2023.108998
9. [9]
  Jingxuan Liu , Shiqi Zhao , Xiang Wu . Flexible electrochemical capacitor based NiMoSSe electrode material with superior cycling and structural stability. Chinese Chemical Letters, 2024, 35(7): 109059-. doi: 10.1016/j.cclet.2023.109059
10. [10]
  Xiaoyu Chen , Jiahao Hu , Jingyi Lin , Haiyang Huang , Changqing Ye , Hongli Bao . Biisoindolylidene solvatochromic fluorophores: Synthesis and photophysical properties. Chinese Chemical Letters, 2025, 36(2): 109923-. doi: 10.1016/j.cclet.2024.109923
11. [11]
  Xinpin Pan , Yongjian Cui , Zhe Wang , Bowen Li , Hailong Wang , Jian Hao , Feng Li , Jing Li . Robust chemo-mechanical stability of additives-free SiO₂ anode realized by honeycomb nanolattice for high performance Li-ion batteries. Chinese Chemical Letters, 2024, 35(10): 109567-. doi: 10.1016/j.cclet.2024.109567
12. [12]
  Ziyang Yin , Lingbin Xie , Weinan Yin , Ting Zhi , Kang Chen , Junan Pan , Yingbo Zhang , Jingwen Li , Longlu Wang . Advanced development of grain boundaries in TMDs from fundamentals to hydrogen evolution application. Chinese Chemical Letters, 2024, 35(5): 108628-. doi: 10.1016/j.cclet.2023.108628
13. [13]
  Botao Gao , He Qi , Hui Liu , Jun Chen . Role of polarization evolution in the hysteresis effect of Pb-based antiferroelecrtics. Chinese Chemical Letters, 2024, 35(4): 108598-. doi: 10.1016/j.cclet.2023.108598
14. [14]
  Ziyou Zhang , Te Ji , Hongliang Dong , Zhiqiang Chen , Zhi Su . Effect of coordination restriction on pressure-induced fluorescence evolution. Chinese Chemical Letters, 2024, 35(12): 109542-. doi: 10.1016/j.cclet.2024.109542
15. [15]
  Guoliang Gao , Guangzhen Zhao , Guang Zhu , Bowen Sun , Zixu Sun , Shunli Li , Ya-Qian Lan . Recent advancements in noble-metal electrocatalysts for alkaline hydrogen evolution reaction. Chinese Chemical Letters, 2025, 36(1): 109557-. doi: 10.1016/j.cclet.2024.109557
16. [16]
  Jing Cao , Dezheng Zhang , Bianqing Ren , Ping Song , Weilin Xu . Mn incorporated RuO₂ nanocrystals as an efficient and stable bifunctional electrocatalyst for oxygen evolution reaction and hydrogen evolution reaction in acid and alkaline. Chinese Chemical Letters, 2024, 35(10): 109863-. doi: 10.1016/j.cclet.2024.109863
17. [17]
  Pu Zhang , Xiang Mao , Xuehua Dong , Ling Huang , Liling Cao , Daojiang Gao , Guohong Zou . Two UV organic-inorganic hybrid antimony-based materials with superior optical performance derived from cation-anion synergetic interactions. Chinese Chemical Letters, 2024, 35(9): 109235-. doi: 10.1016/j.cclet.2023.109235
18. [18]
  Liang Ming , Dan Liu , Qiyue Luo , Chaochao Wei , Chen Liu , Ziling Jiang , Zhongkai Wu , Lin Li , Long Zhang , Shijie Cheng , Chuang Yu . Si-doped Li₆PS₅I with enhanced conductivity enables superior performance for all-solid-state lithium batteries. Chinese Chemical Letters, 2024, 35(10): 109387-. doi: 10.1016/j.cclet.2023.109387
19. [19]
  Wenzhong Zhang , Zirui Yan , Lingcheng Chen , Yi Xiao . Sn-fused perylene diimides: Synthesis, mechanism, and properties. Chinese Chemical Letters, 2024, 35(10): 109582-. doi: 10.1016/j.cclet.2024.109582
20. [20]
  Rongjian Chen , Jiahui Liu , Caixia Lin , Yuanming Li , Yanhou Geng , Yaofeng Yuan . Synthesis and properties of tetraphenylethene cationic cyclophanes based on o-carborane skeleton. Chinese Chemical Letters, 2024, 35(12): 110074-. doi: 10.1016/j.cclet.2024.110074

Get Citation

PDF

XML

Metrics

PDF Downloads(0)
Abstract views(786)
HTML views(26)

通讯作者: 陈斌, bchen63@163.com

1.
沈阳化工大学材料科学与工程学院沈阳 110142