Login In
2016 Volume 34 Issue 9
2016, 34(9): 1047-1059
doi: 10.1007/s10118-016-1827-z
Abstract:
In this study, multiwalled carbon nanotubes (MWCNTs) were used to encapsulate a model anticancer drug, doxorubicin (Dox). Then, the drug-loaded MWCNTs (Dox/MWCNTs) with an optimized drug encapsulation percentage were mixed with poly(lactide-co-glycolide) (PLGA) polymer solution for subsequent electrospinning to form drug-loaded composite nanofibrous mats. The structure, morphology, and mechanical properties of the formed electrospun Dox/PLGA, MWCNTs/PLGA, and Dox/MWCNTs/PLGA composite nanofibrous mats were characterized using scanning electron microscopy (SEM), Fourier transform infrared spectroscopy, and tensile testing. In vitro viability assay and SEM morphology observation of mouse fibroblast cells cultured onto the MWCNTs/PLGA fibrous scaffolds demonstrate that the developed MWCNTs/PLGA composite nanofibers are cytocompatible. The incorporation of Dox-loaded MWCNTs within the PLGA nanofibers is able to improve the mechanical durability and maintain the three-dimensional structure of the nanofibrous mats. More importantly, our results indicate that this double-container drug delivery system (both PLGA polymer and MWCNTs are drug carriers) is beneficial to avoid the burst release of the drug and able to release the antitumor drug Dox in a sustained manner for 42 days. The developed composite electrospun nanofibrous drug delivery system may be used as therapeutic scaffold materials for post-operative local chemotherapy.
In this study, multiwalled carbon nanotubes (MWCNTs) were used to encapsulate a model anticancer drug, doxorubicin (Dox). Then, the drug-loaded MWCNTs (Dox/MWCNTs) with an optimized drug encapsulation percentage were mixed with poly(lactide-co-glycolide) (PLGA) polymer solution for subsequent electrospinning to form drug-loaded composite nanofibrous mats. The structure, morphology, and mechanical properties of the formed electrospun Dox/PLGA, MWCNTs/PLGA, and Dox/MWCNTs/PLGA composite nanofibrous mats were characterized using scanning electron microscopy (SEM), Fourier transform infrared spectroscopy, and tensile testing. In vitro viability assay and SEM morphology observation of mouse fibroblast cells cultured onto the MWCNTs/PLGA fibrous scaffolds demonstrate that the developed MWCNTs/PLGA composite nanofibers are cytocompatible. The incorporation of Dox-loaded MWCNTs within the PLGA nanofibers is able to improve the mechanical durability and maintain the three-dimensional structure of the nanofibrous mats. More importantly, our results indicate that this double-container drug delivery system (both PLGA polymer and MWCNTs are drug carriers) is beneficial to avoid the burst release of the drug and able to release the antitumor drug Dox in a sustained manner for 42 days. The developed composite electrospun nanofibrous drug delivery system may be used as therapeutic scaffold materials for post-operative local chemotherapy.
2016, 34(9): 1060-1069
doi: 10.1007/s10118-016-1825-1
Abstract:
Cobalt and nickel complexes (1a-1d and 2a-2d, respectively) supported by 2-imidate-pyridine ligands were synthesized and used for 1,3-butadiene polymerization. The complexes were characterized by IR and element analysis, and complex 1a was further characterized by single-crystal X-ray diffraction. The solid state structure of complex 1a displayed a distorted tetrahedral geometry. Upon activation with ethylaluminum sesquichloride (EASC), all the complexes showed high activities toward 1,3-butadiene polymerization. The cobalt complexes produced polymers with high cis-1,4 contents and high molecular weights, while the nickel complexes displayed low cis-1,4 selectivity and the resulting polymers had low molecular weights. The catalytic activities of the complexes highly depended on the ligand structure. With the increment of polymerization temperature, the cis-1,4 content and the molecular weight of the resulting polymer decreased.
Cobalt and nickel complexes (1a-1d and 2a-2d, respectively) supported by 2-imidate-pyridine ligands were synthesized and used for 1,3-butadiene polymerization. The complexes were characterized by IR and element analysis, and complex 1a was further characterized by single-crystal X-ray diffraction. The solid state structure of complex 1a displayed a distorted tetrahedral geometry. Upon activation with ethylaluminum sesquichloride (EASC), all the complexes showed high activities toward 1,3-butadiene polymerization. The cobalt complexes produced polymers with high cis-1,4 contents and high molecular weights, while the nickel complexes displayed low cis-1,4 selectivity and the resulting polymers had low molecular weights. The catalytic activities of the complexes highly depended on the ligand structure. With the increment of polymerization temperature, the cis-1,4 content and the molecular weight of the resulting polymer decreased.
2016, 34(9): 1070-1078
doi: 10.1007/s10118-016-1822-4
Abstract:
Poly(ether urethane)s (PEU), including PEUI15 and PEUH15, were prepared through chain-extension reaction of poly(ethylene glycol) (PEG-1500) using diisocyanate as a chain extender, including isophorone diisocyanate (IPDI) and hexamethylene diisocyanate (HDI). These PEUs were used to toughen polylactide (PLA) by physical and reactive blending. Thermal, morphological, mechanical and aging properties of the blends were investigated in detail. These PEUs were partially compatible with PLA. The elongation at break of the reactive blends in the presence of triphenyl phosphate (TPP) for PLA with PEUH15 or PEUI15 was much higher than that of the physical blends. The aging test was carried out at-20℃ for 50h in order to accelerate the crystallization of PEUs. The PEUs in the PLA/PEU blends produced crystallization and formed new phase separation with PLA, resulting in the declined toughness of blends. Fortunately, under the aging condition, although PEUH15 in blends could also form crystallization, the reactive blend of PLA/PEUH15/TPP(80/20/2) had higher toughness than the other blends. The elongation at break of PLA/PEUH15/TPP(80/20/2) dropped to 287% for the aging blend from 350% for the original blend. The tensile strength and modulus of PLA/PEUH15/TPP blend did not change obviously because of the crystallization of PEUH15.
Poly(ether urethane)s (PEU), including PEUI15 and PEUH15, were prepared through chain-extension reaction of poly(ethylene glycol) (PEG-1500) using diisocyanate as a chain extender, including isophorone diisocyanate (IPDI) and hexamethylene diisocyanate (HDI). These PEUs were used to toughen polylactide (PLA) by physical and reactive blending. Thermal, morphological, mechanical and aging properties of the blends were investigated in detail. These PEUs were partially compatible with PLA. The elongation at break of the reactive blends in the presence of triphenyl phosphate (TPP) for PLA with PEUH15 or PEUI15 was much higher than that of the physical blends. The aging test was carried out at-20℃ for 50h in order to accelerate the crystallization of PEUs. The PEUs in the PLA/PEU blends produced crystallization and formed new phase separation with PLA, resulting in the declined toughness of blends. Fortunately, under the aging condition, although PEUH15 in blends could also form crystallization, the reactive blend of PLA/PEUH15/TPP(80/20/2) had higher toughness than the other blends. The elongation at break of PLA/PEUH15/TPP(80/20/2) dropped to 287% for the aging blend from 350% for the original blend. The tensile strength and modulus of PLA/PEUH15/TPP blend did not change obviously because of the crystallization of PEUH15.
2016, 34(9): 1079-1090
doi: 10.1007/s10118-016-1824-2
Abstract:
The hybrid structures of polystyrene-b-poly(ethylene oxide) (PS-b-PEO) block copolymer and inorganic nanoparticles with good stability and biocompatibility have potential applications in drug delivery and bioimaging. Spherical co-assemblies of PS120-b-PEO318 and oleylamine-capped CdS quantum dots (QDs) are produced successfully in this work by adding water to a mixed common solvent, such as N,N-dimethylmethanamide (DMF)/chloroform, DMF/tetrahydrofuran (THF), or DMF/toluene. The energy dispersive X-ray (EDX) spectrum indicates that QDs are located at the interface between the core and shell of the spherical co-assemblies. The co-assembly process during water addition is traced by transmission electron microscopy (TEM) and turbidity measurement. Spherical co-assemblies are formed through budding from bilayers of the block copolymer and QDs. The morphology of the co-assemblies is related to the miscibility of the QD-dispersing solvents with water and the morphology changes from a spherical to a vesicle-like structure with DMF/toluene. Increasing THF content in the mixed solvent causes morphological transitions from spherical co-assemblies to multi-branched cylinders and micelles where QDs are located in the central core. Increasing chloroform content yields vesicle-like structures with protruding rods on the surface. The mechanism of the morphological transitions is also discussed in detail.
The hybrid structures of polystyrene-b-poly(ethylene oxide) (PS-b-PEO) block copolymer and inorganic nanoparticles with good stability and biocompatibility have potential applications in drug delivery and bioimaging. Spherical co-assemblies of PS120-b-PEO318 and oleylamine-capped CdS quantum dots (QDs) are produced successfully in this work by adding water to a mixed common solvent, such as N,N-dimethylmethanamide (DMF)/chloroform, DMF/tetrahydrofuran (THF), or DMF/toluene. The energy dispersive X-ray (EDX) spectrum indicates that QDs are located at the interface between the core and shell of the spherical co-assemblies. The co-assembly process during water addition is traced by transmission electron microscopy (TEM) and turbidity measurement. Spherical co-assemblies are formed through budding from bilayers of the block copolymer and QDs. The morphology of the co-assemblies is related to the miscibility of the QD-dispersing solvents with water and the morphology changes from a spherical to a vesicle-like structure with DMF/toluene. Increasing THF content in the mixed solvent causes morphological transitions from spherical co-assemblies to multi-branched cylinders and micelles where QDs are located in the central core. Increasing chloroform content yields vesicle-like structures with protruding rods on the surface. The mechanism of the morphological transitions is also discussed in detail.
2016, 34(9): 1091-1102
doi: 10.1007/s10118-016-1833-1
Abstract:
Five novel near-infrared electrochromic aromatic polyimides (PIs) with pendent benzimidazole group were synthesized from 4,4'-diamino-4''-(1-benzylbenzimidazol-2-yl)triphenylamine (named as DBBT) with five different dianhydrides via two-step polymerization process, respectively. The maximum UV-Vis absorption bands of these PIs locate at about 335 nm for solid films due to the π-π* transitions. A reversible pair of distinct redox peaks, that were associated with a noticeable color change from original yellow to blue, was observed in the cyclic voltammetry (CV) test. A new absorption peak emerged at 847 nm in near-infrared (NIR) region with increasing voltage in UV-Vis-NIR spectrum, which indicates that PI can be used as NIR electrochromic material. These novel PIs have good electrochemical stability, appropriate energy levels for the highest occupied molecular orbital (HOMO) and the lowest unoccupied molecular orbital (LUMO), in the range of-5.17 eV to-5.20 eV and-2.14 eV to-2.26 eV (versus the vacuum level) determined by cyclic voltammetry method. These values basically consisted with the results of quantum chemical calculation. These polyimides can be used as novel electrochromic and hole transportation materials.
Five novel near-infrared electrochromic aromatic polyimides (PIs) with pendent benzimidazole group were synthesized from 4,4'-diamino-4''-(1-benzylbenzimidazol-2-yl)triphenylamine (named as DBBT) with five different dianhydrides via two-step polymerization process, respectively. The maximum UV-Vis absorption bands of these PIs locate at about 335 nm for solid films due to the π-π* transitions. A reversible pair of distinct redox peaks, that were associated with a noticeable color change from original yellow to blue, was observed in the cyclic voltammetry (CV) test. A new absorption peak emerged at 847 nm in near-infrared (NIR) region with increasing voltage in UV-Vis-NIR spectrum, which indicates that PI can be used as NIR electrochromic material. These novel PIs have good electrochemical stability, appropriate energy levels for the highest occupied molecular orbital (HOMO) and the lowest unoccupied molecular orbital (LUMO), in the range of-5.17 eV to-5.20 eV and-2.14 eV to-2.26 eV (versus the vacuum level) determined by cyclic voltammetry method. These values basically consisted with the results of quantum chemical calculation. These polyimides can be used as novel electrochromic and hole transportation materials.
2016, 34(9): 1103-1116
doi: 10.1007/s10118-016-1832-2
Abstract:
Carborane bisphenol novolacs (3 and 4) were synthesized in the presence of acid catalyst from carborane bisphenols (5 and 6) and formaldehyde. Further epoxidization of carborane bisphenol novolacs with epichlorohydrin gave carborane bisphenol epoxy novolacs (1 and 2). The molecular weight and epoxy value of obtained resins were determined using the molecular weight of their precursors. The epoxy values of 1 and 2 were 0.48 and 0.52 respectively, higher than the maximum theoretical epoxy value (0.45) of difunctional carborane bisphenol epoxy resins. FTIR and NMR were utilized to characterize 1 and 2. The curing behaviors were also studied by DSC and the optimized curing conditions were obtained. TGA analysis indicated that carborane moiety could shield its adjacent organic structures against initial decomposition. On the other hand, B―H on carborane cage could react with oxygen to form a three-dimensional network linked by B―O―B and B―C bonds, which further blocked the movement of formed radicals and thus the degradation process was inhibited.
Carborane bisphenol novolacs (3 and 4) were synthesized in the presence of acid catalyst from carborane bisphenols (5 and 6) and formaldehyde. Further epoxidization of carborane bisphenol novolacs with epichlorohydrin gave carborane bisphenol epoxy novolacs (1 and 2). The molecular weight and epoxy value of obtained resins were determined using the molecular weight of their precursors. The epoxy values of 1 and 2 were 0.48 and 0.52 respectively, higher than the maximum theoretical epoxy value (0.45) of difunctional carborane bisphenol epoxy resins. FTIR and NMR were utilized to characterize 1 and 2. The curing behaviors were also studied by DSC and the optimized curing conditions were obtained. TGA analysis indicated that carborane moiety could shield its adjacent organic structures against initial decomposition. On the other hand, B―H on carborane cage could react with oxygen to form a three-dimensional network linked by B―O―B and B―C bonds, which further blocked the movement of formed radicals and thus the degradation process was inhibited.
2016, 34(9): 1117-1128
doi: 10.1007/s10118-016-1819-z
Abstract:
Crosslinking reactions of high density polyethylene with low peroxide concentrations ranging from 0.1 wt% to 1.0 wt% at temperatures of 170, 180 and 190℃ were monitored by rheological measurements. A critical gel forms at the peroxide concentration of 0.2 wt%, where the transition from long chain branching generation to crosslinking network formation could occur. Rheokinetics of crosslinking can be fitted well by Ding-Leonov’s model. The curing rate k2 at the earlier stage exhibits about 3 times acceleration per 10℃ with increasing temperature, while the equilibrium modulus G′at the fully cured stage is almost independent of temperature. Influences of crosslinking on the subsequent crystallization behaviors were detected by DSC measurements. Above the critical gel concentration, crystallization is largely retarded as evidenced by the lower crystallization temperature Tc and crystallinity Xc due to the network formation. The secondary crystallization valley located at the temperature near 80℃ can be observed above the critical concentration, which becomes more evident with the increasing peroxide concentration and curing temperature. This phenomenon provides another evidence of crystallization retardation by the crosslinking network.
Crosslinking reactions of high density polyethylene with low peroxide concentrations ranging from 0.1 wt% to 1.0 wt% at temperatures of 170, 180 and 190℃ were monitored by rheological measurements. A critical gel forms at the peroxide concentration of 0.2 wt%, where the transition from long chain branching generation to crosslinking network formation could occur. Rheokinetics of crosslinking can be fitted well by Ding-Leonov’s model. The curing rate k2 at the earlier stage exhibits about 3 times acceleration per 10℃ with increasing temperature, while the equilibrium modulus G′at the fully cured stage is almost independent of temperature. Influences of crosslinking on the subsequent crystallization behaviors were detected by DSC measurements. Above the critical gel concentration, crystallization is largely retarded as evidenced by the lower crystallization temperature Tc and crystallinity Xc due to the network formation. The secondary crystallization valley located at the temperature near 80℃ can be observed above the critical concentration, which becomes more evident with the increasing peroxide concentration and curing temperature. This phenomenon provides another evidence of crystallization retardation by the crosslinking network.
2016, 34(9): 1129-1140
doi: 10.1007/s10118-016-1834-0
Abstract:
Polylactide (PLA) films blended with 10 wt% poly(butylene adipate-co-terephthalate) (PBAT) were prepared by using a twin screw extruder in the presence of the nucleating agent of titanium dioxide (TiO2) and the compatibilizers of toluene diisocyanate (TDI) and PLA-grafted-maleic anhydride (PLA-g-MA). The synergistic effect of the nucleation and compatibilization on the properties and crystallization behavior of the PLA/PBAT (PLB) films was explored. The results showed that the addition of TiO2 significantly enhanced the tensile strength and the impact tensile resistance of the PLB films while slightly decreased its thermal stability. In addition, the compatibilizers of TDI and PLA-g-MA in the system not only affected the crystallinity and cold crystallization process of the PLB films, but also increased the mechanical properties of them due to the improvement of the interfacial interaction between PLA and PBAT revealed by the morphological measurement. The synergistic effects of the nucleating agent and the compatibilizer afforded the blend films with increased tensile strength and impact tensile toughness, improved cold crystallization property and cc.
Polylactide (PLA) films blended with 10 wt% poly(butylene adipate-co-terephthalate) (PBAT) were prepared by using a twin screw extruder in the presence of the nucleating agent of titanium dioxide (TiO2) and the compatibilizers of toluene diisocyanate (TDI) and PLA-grafted-maleic anhydride (PLA-g-MA). The synergistic effect of the nucleation and compatibilization on the properties and crystallization behavior of the PLA/PBAT (PLB) films was explored. The results showed that the addition of TiO2 significantly enhanced the tensile strength and the impact tensile resistance of the PLB films while slightly decreased its thermal stability. In addition, the compatibilizers of TDI and PLA-g-MA in the system not only affected the crystallinity and cold crystallization process of the PLB films, but also increased the mechanical properties of them due to the improvement of the interfacial interaction between PLA and PBAT revealed by the morphological measurement. The synergistic effects of the nucleating agent and the compatibilizer afforded the blend films with increased tensile strength and impact tensile toughness, improved cold crystallization property and cc.
2016, 34(9): 1141-1149
doi: 10.1007/s10118-016-1823-3
Abstract:
Solvent annealing is a facile method for changing the aggregated microstructure and physical properties of polymer materials. In this paper, we addressed the effects of solvent vapor annealing, including chloroform and water vapor, on the polymorphic transformation in both hot-pressed film and electrospun nonwoven of isotactic polybutene-1 (PB-1) by means of in situ Fourier transform infrared spectroscopy (FTIR). The pretty rapid transition rate caused by the increased motion of molecular chains under chloroform vapor is associated with a lowest crystallinity. Also, a decreased crystallinity with the crystal transition occurred in electrospun nonwovens resulting from the relaxation of the stretched molecular chains into amorphous state rather than realignment into crystal form I predominating the crystal transition process.
Solvent annealing is a facile method for changing the aggregated microstructure and physical properties of polymer materials. In this paper, we addressed the effects of solvent vapor annealing, including chloroform and water vapor, on the polymorphic transformation in both hot-pressed film and electrospun nonwoven of isotactic polybutene-1 (PB-1) by means of in situ Fourier transform infrared spectroscopy (FTIR). The pretty rapid transition rate caused by the increased motion of molecular chains under chloroform vapor is associated with a lowest crystallinity. Also, a decreased crystallinity with the crystal transition occurred in electrospun nonwovens resulting from the relaxation of the stretched molecular chains into amorphous state rather than realignment into crystal form I predominating the crystal transition process.
2016, 34(9): 1150-1157
doi: 10.1007/s10118-016-1831-3
Abstract:
We propose a simple and effective boundary model in a nonequilibrium molecular dynamics (NEMD) simulation to study the out-of-equilibrium dynamics of polymer fluids. The present boundary model can effectively weaken the depletion effect and the slip effect near the boundary, and remove the unwanted heat instantly. The validity of the boundary model is checked by investigating the flow behavior of dilute polymer solution driven by an external force. Reasonable density distributions of both polymer and solvent particles, velocity profiles of the solvent and temperature profiles of the system are obtained. Furthermore, the studied polymer chain shows a cross-streaming migration towards center of the tube, which is consistent with that predicted in previous literatures. These numerical results give powerful evidences for the validity of the present boundary model. Besides, the boundary model can also be used in other flows in addition to the Poiseuille flow.
We propose a simple and effective boundary model in a nonequilibrium molecular dynamics (NEMD) simulation to study the out-of-equilibrium dynamics of polymer fluids. The present boundary model can effectively weaken the depletion effect and the slip effect near the boundary, and remove the unwanted heat instantly. The validity of the boundary model is checked by investigating the flow behavior of dilute polymer solution driven by an external force. Reasonable density distributions of both polymer and solvent particles, velocity profiles of the solvent and temperature profiles of the system are obtained. Furthermore, the studied polymer chain shows a cross-streaming migration towards center of the tube, which is consistent with that predicted in previous literatures. These numerical results give powerful evidences for the validity of the present boundary model. Besides, the boundary model can also be used in other flows in addition to the Poiseuille flow.
2016, 34(9): 1158-1171
doi: 10.1007/s10118-016-1830-4
Abstract:
Long chain branched polypropylene random copolymers (LCB-PPRs) were prepared via reactive extrusion with the addition of dicumyl peroxide (DCP) and various amounts of 1,6-hexanediol diacrylate (HDDA) into PPR. Fourier transform infrared spectrometer (FTIR) was applied to confirm the existence of branching and investigate the grafting degree for the modified PPRs. Melt flow index (MFI) and oscillatory shear rheological properties including complex viscosity, storage modulus, loss tangent and the Cole-Cole plots were studied to differentiate the LCB-PPRs from linear PPR. Differential scanning calorimetry (DSC) and polarized light microscopy (PLM) were used to study the melting and crystallization behavior and the spherulite morphology, respectively. Qualitative and quantitative analyses of rheological curves demonstrated the existence of LCB. The effect of the LCB on crystalline morphology, crystallization behavior and molecular mobility, and, thereby, the mechanical properties were studied and analyzed. Due to the entanglements between molecular chains and the nucleating effect of LCB, LCB-PPRs showed higher crystallization temperature and crystallinity, higher crystallization rate, more uniformly dispersed and much smaller crystallite compared with virgin PPR, thus giving rise to significantly improve impact strength. Moreover, the LCB-PPRs exhibited the improved yield strength. The mobility of the molecular chain segments, as demonstrated by dynamic mechanical analysis (DMA), was improved for the modified PPRs, which also contributed to the improvement of their mechanical properties.
Long chain branched polypropylene random copolymers (LCB-PPRs) were prepared via reactive extrusion with the addition of dicumyl peroxide (DCP) and various amounts of 1,6-hexanediol diacrylate (HDDA) into PPR. Fourier transform infrared spectrometer (FTIR) was applied to confirm the existence of branching and investigate the grafting degree for the modified PPRs. Melt flow index (MFI) and oscillatory shear rheological properties including complex viscosity, storage modulus, loss tangent and the Cole-Cole plots were studied to differentiate the LCB-PPRs from linear PPR. Differential scanning calorimetry (DSC) and polarized light microscopy (PLM) were used to study the melting and crystallization behavior and the spherulite morphology, respectively. Qualitative and quantitative analyses of rheological curves demonstrated the existence of LCB. The effect of the LCB on crystalline morphology, crystallization behavior and molecular mobility, and, thereby, the mechanical properties were studied and analyzed. Due to the entanglements between molecular chains and the nucleating effect of LCB, LCB-PPRs showed higher crystallization temperature and crystallinity, higher crystallization rate, more uniformly dispersed and much smaller crystallite compared with virgin PPR, thus giving rise to significantly improve impact strength. Moreover, the LCB-PPRs exhibited the improved yield strength. The mobility of the molecular chain segments, as demonstrated by dynamic mechanical analysis (DMA), was improved for the modified PPRs, which also contributed to the improvement of their mechanical properties.
2016, 34(9): 1172-1182
doi: 10.1007/s10118-016-1820-6
Abstract:
Poly(trimethylene terephthalate)/polycarbonate (PTT/PC) blends were prepared by solvent mixing to avoid transesterification during high temperature blending. The influences of compositions on the thermal behavior, crystallization morphology and structure of the blends were studied. FTIR results indicated that there was no COO linking to two phenyl groups on each side chain and DSC results supported no transesterification reaction. DSC curves showed that Tc and Tmc increased to maximum range when PC contents were between 7 wt%-15 wt%, however, Tm decreased constantly with the increase of PC contents. It was observed from POM that PTT spherulitic morphology and crystallization kinetics were obviously influenced by the change of PC contents. Structural evolutions during cooling were investigated by SAXS which showed Lc of PTT remained a constant with different PC contents and also fixed during crystallization, nevertheless, it revealed a maximum value of Lnc for sample PTT93. It was concluded that PC chains could be permeated into not only amorphous crystallite structure but also amorphous lamellae structure and 7 wt% PC content was supposed to be the "proper" penetration amount into PTT lamellae structure which led to a maximum capacity of amorphous lamellar layer. Fringed-micelle crystal model was adopted to illustrate semi-crystalline physical structures of the blend in two kinds of component aggregation states.
Poly(trimethylene terephthalate)/polycarbonate (PTT/PC) blends were prepared by solvent mixing to avoid transesterification during high temperature blending. The influences of compositions on the thermal behavior, crystallization morphology and structure of the blends were studied. FTIR results indicated that there was no COO linking to two phenyl groups on each side chain and DSC results supported no transesterification reaction. DSC curves showed that Tc and Tmc increased to maximum range when PC contents were between 7 wt%-15 wt%, however, Tm decreased constantly with the increase of PC contents. It was observed from POM that PTT spherulitic morphology and crystallization kinetics were obviously influenced by the change of PC contents. Structural evolutions during cooling were investigated by SAXS which showed Lc of PTT remained a constant with different PC contents and also fixed during crystallization, nevertheless, it revealed a maximum value of Lnc for sample PTT93. It was concluded that PC chains could be permeated into not only amorphous crystallite structure but also amorphous lamellae structure and 7 wt% PC content was supposed to be the "proper" penetration amount into PTT lamellae structure which led to a maximum capacity of amorphous lamellar layer. Fringed-micelle crystal model was adopted to illustrate semi-crystalline physical structures of the blend in two kinds of component aggregation states.
