Login In
2004 Volume 22 Issue 4
2004, 22(4): 305-308
Abstract:
A series of Ti/Mg supported catalysts are prepared by using ball-milled mixtures of MgCl2-ethanol adducts and NaCl as supports, and 1-hexene polymerizations catalyzed by the novel catalysts are studied. It is found that the molecular weight distribution of poly(1-hexene) becomes apparently narrower when catalysts with doped supports are used, indicating that changing the structure of the support is an effective way to regulate the active center distribution of heterogeneous Ziegler-Natta catalyst.
A series of Ti/Mg supported catalysts are prepared by using ball-milled mixtures of MgCl2-ethanol adducts and NaCl as supports, and 1-hexene polymerizations catalyzed by the novel catalysts are studied. It is found that the molecular weight distribution of poly(1-hexene) becomes apparently narrower when catalysts with doped supports are used, indicating that changing the structure of the support is an effective way to regulate the active center distribution of heterogeneous Ziegler-Natta catalyst.
2004, 22(4): 309-312
Abstract:
An overview of aqueous polymerizations, which include emulsion, miniemulsion and suspension polymerizations,under stable free radical polymerization (SFRP) conditions is presented. The success of miniemulsion and suspension SFRP polymerizations is contrasted with the difficulties associated with obtaining a stable emulsion polymerization. A recently developed unique microprecipitation technique is referenced as a means of making submicron sized particles that can be used to achieve a stable emulsion SFRP process.
An overview of aqueous polymerizations, which include emulsion, miniemulsion and suspension polymerizations,under stable free radical polymerization (SFRP) conditions is presented. The success of miniemulsion and suspension SFRP polymerizations is contrasted with the difficulties associated with obtaining a stable emulsion polymerization. A recently developed unique microprecipitation technique is referenced as a means of making submicron sized particles that can be used to achieve a stable emulsion SFRP process.
2004, 22(4): 313-319
Abstract:
(α-Diimine)nickel(Ⅱ) {[C6H5-N = C(CH3)- C(CH3) = N - C6H5]NiBr2}-TiCl4, abbreviated as NiL-TiCl4combined catalyst which is supported on MgCl2-SiO2 carrier has been prepared, by using alkyl aluminum (AlR3) as the cocatalyst in place of methylaluminoxane (MAO) to catalyze ethylene oligomerization and copolymerization in situ. The influences of procedure for supporting NiL-TiCl4, the molar ratio of NiL to TiCl4, cocatalyst type and polymerization temperature on the catalytic performance were studied. The degree of branching and the composition of the branched chain of polymers produced have been investigated by IR and 13C-NMR spectra. The results show that the combined catalyst can synthesize the branched polyethylene with various banched chains .The polymerization reaction was monitored by gas chromatography and mass spectrometry (GC-MS). The results show that this catalyst promotes the oligomerization and copolymerization in situ for ethylene.
(α-Diimine)nickel(Ⅱ) {[C6H5-N = C(CH3)- C(CH3) = N - C6H5]NiBr2}-TiCl4, abbreviated as NiL-TiCl4combined catalyst which is supported on MgCl2-SiO2 carrier has been prepared, by using alkyl aluminum (AlR3) as the cocatalyst in place of methylaluminoxane (MAO) to catalyze ethylene oligomerization and copolymerization in situ. The influences of procedure for supporting NiL-TiCl4, the molar ratio of NiL to TiCl4, cocatalyst type and polymerization temperature on the catalytic performance were studied. The degree of branching and the composition of the branched chain of polymers produced have been investigated by IR and 13C-NMR spectra. The results show that the combined catalyst can synthesize the branched polyethylene with various banched chains .The polymerization reaction was monitored by gas chromatography and mass spectrometry (GC-MS). The results show that this catalyst promotes the oligomerization and copolymerization in situ for ethylene.
2004, 22(4): 321-325
Abstract:
Poly(methyltetraphenylphenylsilylene-co-bis(methylphenylsilyl)acetylene) (PSA) was synthesized by the cocondensation reaction of methyltetraphenylphenyldichlorosilane and bis(chloromethylphenylsilyl)acetylene with sodium in toluene. The PSA thus obtained was soluble in most organic solvents, and its molecular weight was smaller than that of poly[(disilanylene)acetylenes] with alkyl- or aryl-substitution because of the great steric congestion of tetraphenylphenyl groups. The optical and electronic properties of the polymer were investigated. The results show that PSA has strong UV absorption and fluorescence emission, the maximum UV absorption wavelength of PSA is 330 nm, which shows a considerable red-shift in comparison with that of poly(methylphenylsilylene-co-methylphenylsilylacetylene) (PSI) and alkyl- substituted poly[(disilanylene)acetylenes]. A strong photoluminescence band at 470 nm in THF and 432 nm in benzene can be observed in the visible region, respectively. Treatment of the films of PSA with I2 vapor afforded conducting films. The conductivity of PSA thin film doped with I2 was measured to be 0.35 S cm-1 in the air which is lower than that of poly(methyltetraphenylphenylsilylene-co-bis(methylphenylsilyl)phenylene), but higher than that of σ-π polymers without tetraphenylphenyl groups. As an explanation, the tetraphenylphenyl group is a large π-electron-conjugated group; after being introduced to the Si atoms of the polysilanes, the interaction between π-electrons of the tetraphenylphenyl groups and the σ-electrons conjugated along the Si—Si bonds is increased strongly, and the σ-electrons can be conjugated more extensively along the main chain of the polysilanes.
Poly(methyltetraphenylphenylsilylene-co-bis(methylphenylsilyl)acetylene) (PSA) was synthesized by the cocondensation reaction of methyltetraphenylphenyldichlorosilane and bis(chloromethylphenylsilyl)acetylene with sodium in toluene. The PSA thus obtained was soluble in most organic solvents, and its molecular weight was smaller than that of poly[(disilanylene)acetylenes] with alkyl- or aryl-substitution because of the great steric congestion of tetraphenylphenyl groups. The optical and electronic properties of the polymer were investigated. The results show that PSA has strong UV absorption and fluorescence emission, the maximum UV absorption wavelength of PSA is 330 nm, which shows a considerable red-shift in comparison with that of poly(methylphenylsilylene-co-methylphenylsilylacetylene) (PSI) and alkyl- substituted poly[(disilanylene)acetylenes]. A strong photoluminescence band at 470 nm in THF and 432 nm in benzene can be observed in the visible region, respectively. Treatment of the films of PSA with I2 vapor afforded conducting films. The conductivity of PSA thin film doped with I2 was measured to be 0.35 S cm-1 in the air which is lower than that of poly(methyltetraphenylphenylsilylene-co-bis(methylphenylsilyl)phenylene), but higher than that of σ-π polymers without tetraphenylphenyl groups. As an explanation, the tetraphenylphenyl group is a large π-electron-conjugated group; after being introduced to the Si atoms of the polysilanes, the interaction between π-electrons of the tetraphenylphenyl groups and the σ-electrons conjugated along the Si—Si bonds is increased strongly, and the σ-electrons can be conjugated more extensively along the main chain of the polysilanes.
2004, 22(4): 327-331
Abstract:
Polymer(I)and polymer(Ⅱ) were obtained by the polymerization of (R)-6,6'-dibromo-2,2'-binaphtho-20-crown-6(M-1) and (R)-6,6'-dibromo-2,2'-di(methoxyethoxymethyloxy)-1,1'-binaphthyl (M-2) with p-divinylbenzene under Pd-catalyzed Heck reaction. The UV, fluorescence and CD spectra of polymer(I) and(Ⅱ) are similar due to the same linkers present in their polymer chain. Polymers (I) and(Ⅱ) can emit strong blue fluorescence and are expected to have potential applications in polarized blue-light emitting sensors. The chiral conjugated polymers (I) and(Ⅱ) exhibit a strong Cotton effect in their circular dichroism (CD) spectra, indicating a high rigidity of polymer backbone.
Polymer(I)and polymer(Ⅱ) were obtained by the polymerization of (R)-6,6'-dibromo-2,2'-binaphtho-20-crown-6(M-1) and (R)-6,6'-dibromo-2,2'-di(methoxyethoxymethyloxy)-1,1'-binaphthyl (M-2) with p-divinylbenzene under Pd-catalyzed Heck reaction. The UV, fluorescence and CD spectra of polymer(I) and(Ⅱ) are similar due to the same linkers present in their polymer chain. Polymers (I) and(Ⅱ) can emit strong blue fluorescence and are expected to have potential applications in polarized blue-light emitting sensors. The chiral conjugated polymers (I) and(Ⅱ) exhibit a strong Cotton effect in their circular dichroism (CD) spectra, indicating a high rigidity of polymer backbone.
2004, 22(4): 333-341
Abstract:
In this article, the transesterification of poly(bisphenol A carbonate) (PC) with butylene terephthalate-caprolactone copolyester at a weight ratio 50/50 (BCL(21)) was thoroughly investigated by proton nuclear magnetic resonance spectroscopy (1H-NMR), in conjunction with a model compound. The1H-NMR results of the annealed blend PC/BCL(21)show that the formation of bisphenol A-terephthalate ester units is the same as in the annealed blend of PC with PBT, and the transesterification actually occurs between PC and butylene terephthalate (BT) segments in BCL(21). By comparison with the model compound bisphenol A dibutyrate, the new signal appearing at δ= 2.56 in the 1H-NMR spectrum confirms the existence of bisphenol A caprolactone ester units resulting from the exchange reaction of PC with caprolactone (CL) segments. 1H-NMR analysis of the transesterification rates reveals that the reaction of PC with aromatic and aliphatic segments in BCL(21) proceeds in a random manner. The miscibility of the blend PC/BCL(21) copolyester is favorable for the transesterification of PC with BT segments and CL segments.
In this article, the transesterification of poly(bisphenol A carbonate) (PC) with butylene terephthalate-caprolactone copolyester at a weight ratio 50/50 (BCL(21)) was thoroughly investigated by proton nuclear magnetic resonance spectroscopy (1H-NMR), in conjunction with a model compound. The1H-NMR results of the annealed blend PC/BCL(21)show that the formation of bisphenol A-terephthalate ester units is the same as in the annealed blend of PC with PBT, and the transesterification actually occurs between PC and butylene terephthalate (BT) segments in BCL(21). By comparison with the model compound bisphenol A dibutyrate, the new signal appearing at δ= 2.56 in the 1H-NMR spectrum confirms the existence of bisphenol A caprolactone ester units resulting from the exchange reaction of PC with caprolactone (CL) segments. 1H-NMR analysis of the transesterification rates reveals that the reaction of PC with aromatic and aliphatic segments in BCL(21) proceeds in a random manner. The miscibility of the blend PC/BCL(21) copolyester is favorable for the transesterification of PC with BT segments and CL segments.
2004, 22(4): 343-348
Abstract:
Facile and rapid polycondensation reactions of N,N'-(pyromellitoyl)-bis-L-leucine diacid chloride 1 with eight different derivatives of hydantoin compounds 2a-h were developed by using a domestic microwave oven in the presence of a small amount of polar organic medium such as o-cresol. The polycondensation reactions proceeded rapidly, compared with the conventional solution polycondensation, and was completed within 7-10 min, producing a series of novel optically active poly(amide-imide)s 3a-h with high yield and inherent viscosity of 0.35-0.65 dL/g. All of the above polymers were fully characterized by FT-IR, elemental analyses, inherent viscosity (ηinh), solubility test and specific rotation. Some structural characterization and physical properties of these optically active poly(amide-imide)s are reported.
Facile and rapid polycondensation reactions of N,N'-(pyromellitoyl)-bis-L-leucine diacid chloride 1 with eight different derivatives of hydantoin compounds 2a-h were developed by using a domestic microwave oven in the presence of a small amount of polar organic medium such as o-cresol. The polycondensation reactions proceeded rapidly, compared with the conventional solution polycondensation, and was completed within 7-10 min, producing a series of novel optically active poly(amide-imide)s 3a-h with high yield and inherent viscosity of 0.35-0.65 dL/g. All of the above polymers were fully characterized by FT-IR, elemental analyses, inherent viscosity (ηinh), solubility test and specific rotation. Some structural characterization and physical properties of these optically active poly(amide-imide)s are reported.
2004, 22(4): 349-353
Abstract:
polybenzoxazole (PBO) precursor, hydroxy-substituted polyenaminonitrile, was prepared by direct polycondensation of 1,4-bis(1-chloro-2,2-dicyanovinyl)benzene (CCB) and 4,6-diaminoresorcinol dihydrochloride (DAR)using pyridine and N,N-dimethylacetamide as condensing agent and solvent. The precursor has good solubility in polar aprotic solvent which is due to the strong dipolar nature of the main chain. The soluble precursor was subjected to thermal cyclization in an inert atmosphere to convert it into the corresponding PBO, which has its 5% weight loss temperature at 540℃.The fully cyclized PBO were characterized by FT-IR and TGA. The introduction of 10% mol 1,3,5-benzenetricarboxylic chloride (BTC) into the main chain not only has little effect on the solubility of PBO precursor but also raises its 5% weight loss temperature to 552℃ and char yield at 700℃ for the cyclized PBO with BTC.
polybenzoxazole (PBO) precursor, hydroxy-substituted polyenaminonitrile, was prepared by direct polycondensation of 1,4-bis(1-chloro-2,2-dicyanovinyl)benzene (CCB) and 4,6-diaminoresorcinol dihydrochloride (DAR)using pyridine and N,N-dimethylacetamide as condensing agent and solvent. The precursor has good solubility in polar aprotic solvent which is due to the strong dipolar nature of the main chain. The soluble precursor was subjected to thermal cyclization in an inert atmosphere to convert it into the corresponding PBO, which has its 5% weight loss temperature at 540℃.The fully cyclized PBO were characterized by FT-IR and TGA. The introduction of 10% mol 1,3,5-benzenetricarboxylic chloride (BTC) into the main chain not only has little effect on the solubility of PBO precursor but also raises its 5% weight loss temperature to 552℃ and char yield at 700℃ for the cyclized PBO with BTC.
2004, 22(4): 355-362
Abstract:
Three new kinds of molecular networks are designed and predicted to exhibit negative Poisson ratios. Molecular mechanics calculations on these networks show that the magnitude of Poisson ratios depends on the relative flexibility of beam and arm structures. Several new kinds of auxetic polymers, whose successful synthesis should be easier than that of the corresponding auxetic networks, are then proposed. It is found that the kabob-like polymers with auxegens lying vertically on the main chain can acquire auxeticity while those with auxegens lying horizontally on the main chain cannot. Besides, a half kabob-like or pseudo-ladder polymer with auxegens linked at the intersection of the beam and the arm does show auxeticity when adopting constrictive conformers. It is, however, worthwhile noting that the origins of auxeticity still await and strongly deserve further experimental and theoretical investigations.
Three new kinds of molecular networks are designed and predicted to exhibit negative Poisson ratios. Molecular mechanics calculations on these networks show that the magnitude of Poisson ratios depends on the relative flexibility of beam and arm structures. Several new kinds of auxetic polymers, whose successful synthesis should be easier than that of the corresponding auxetic networks, are then proposed. It is found that the kabob-like polymers with auxegens lying vertically on the main chain can acquire auxeticity while those with auxegens lying horizontally on the main chain cannot. Besides, a half kabob-like or pseudo-ladder polymer with auxegens linked at the intersection of the beam and the arm does show auxeticity when adopting constrictive conformers. It is, however, worthwhile noting that the origins of auxeticity still await and strongly deserve further experimental and theoretical investigations.
2004, 22(4): 363-367
Abstract:
Dynamic rheological characteristics of polypropylene (PP) filled with ultra-fine full-vulcanized powdered rubber (UFPR) composed of styrene-butadiene copolymer were studied through dynamic rheological measurements on an Advanced Rheometric Expansion System (ARES). A specific viscoelastic phenomenon, i.e. "the second plateau", appeared at low frequencies, and exhibits a certain dependence on the amount of rubber particles and the dispersion state in the matrix. This phenomenon is attributed to the formation of aggregation structure of rubber particles. The analyses of Cole-Cole diagrams of the dynamic viscoelastic functions suggest that the heterogeneity of the composites is enhanced on increasing both particle content and temperature.
Dynamic rheological characteristics of polypropylene (PP) filled with ultra-fine full-vulcanized powdered rubber (UFPR) composed of styrene-butadiene copolymer were studied through dynamic rheological measurements on an Advanced Rheometric Expansion System (ARES). A specific viscoelastic phenomenon, i.e. "the second plateau", appeared at low frequencies, and exhibits a certain dependence on the amount of rubber particles and the dispersion state in the matrix. This phenomenon is attributed to the formation of aggregation structure of rubber particles. The analyses of Cole-Cole diagrams of the dynamic viscoelastic functions suggest that the heterogeneity of the composites is enhanced on increasing both particle content and temperature.
2004, 22(4): 369-377
Abstract:
Surface modification of microporous polypropylene hollow fiber membranes was performed by radical-induced graft polymerization of N,N-dimethylaminoethyl methacrylate (DMAEMA). The influences of temperature, monomer concentration and pre-adsorbed amount of benzoyl peroxide on grafting degree were studied respectively. It was found that the appropriate graft temperature was 75℃, at which the grafting degree was the highest and the hydrolytic decomposition of DMAEMA the lowest. Scanning electron photomicrography and the average pore diameters of the modified membranes demonstrated that part of the micropores on the membrane surface was plugged by the grafted polyDMAEMA chains, especially at high grafting degree. Contact angle and water swelling experiments showed that a moderate grafting degree could improve the hydrophilicity of the membranes. In the range of 11.3%-12.0% grafting degree, the water swelling percentage reached its maximum (51.1%) and the contact angle reached its minimum (74 degrees). The bovine serum albumin (BSA) adsorption experiment indicated that the grafted polyDMAEMA had a dual effect on protein adsorption. At the first stage, the BSA adsorption decreased with increasing of DMAEMA grafting degree. As the interaction between BSA and polyDMAEMA on membrane surface increased, the BSA adsorption increased with increasing of DMAEMA grafting degree.
Surface modification of microporous polypropylene hollow fiber membranes was performed by radical-induced graft polymerization of N,N-dimethylaminoethyl methacrylate (DMAEMA). The influences of temperature, monomer concentration and pre-adsorbed amount of benzoyl peroxide on grafting degree were studied respectively. It was found that the appropriate graft temperature was 75℃, at which the grafting degree was the highest and the hydrolytic decomposition of DMAEMA the lowest. Scanning electron photomicrography and the average pore diameters of the modified membranes demonstrated that part of the micropores on the membrane surface was plugged by the grafted polyDMAEMA chains, especially at high grafting degree. Contact angle and water swelling experiments showed that a moderate grafting degree could improve the hydrophilicity of the membranes. In the range of 11.3%-12.0% grafting degree, the water swelling percentage reached its maximum (51.1%) and the contact angle reached its minimum (74 degrees). The bovine serum albumin (BSA) adsorption experiment indicated that the grafted polyDMAEMA had a dual effect on protein adsorption. At the first stage, the BSA adsorption decreased with increasing of DMAEMA grafting degree. As the interaction between BSA and polyDMAEMA on membrane surface increased, the BSA adsorption increased with increasing of DMAEMA grafting degree.
2004, 22(4): 379-387
Abstract:
Structures and crystal form transition of the novel aryl ether ketone polymer containing meta-phenylene linkage:PEKEKK(T/I) were investigated by wide angle X-ray diffraction (WAXD), imaging plates (IPs) and small angle X-ray scattering (SAXS). The energy of activation of the decomposition reaction and degree of crystallinity of PEKEKK(T/I) were determined by WAXD and thermo-gravimetric analysis (TGA), respectively. Results obtained from WAXD and IPs show that crystal forms Ⅰ and Ⅱ coexist in the PEKEKK(T/I) samples isothermally cold crystallized in the temperature range from 180℃ to 240℃ and only form Ⅰ occurs in PEKEKK(TTI) samples isothermally cold crystallized at 270℃ . The radius of gyration (Rg), thickness of microregions with electron-density fluctuations (E) and distribution of particle sizes were investigated by SAXS.
Structures and crystal form transition of the novel aryl ether ketone polymer containing meta-phenylene linkage:PEKEKK(T/I) were investigated by wide angle X-ray diffraction (WAXD), imaging plates (IPs) and small angle X-ray scattering (SAXS). The energy of activation of the decomposition reaction and degree of crystallinity of PEKEKK(T/I) were determined by WAXD and thermo-gravimetric analysis (TGA), respectively. Results obtained from WAXD and IPs show that crystal forms Ⅰ and Ⅱ coexist in the PEKEKK(T/I) samples isothermally cold crystallized in the temperature range from 180℃ to 240℃ and only form Ⅰ occurs in PEKEKK(TTI) samples isothermally cold crystallized at 270℃ . The radius of gyration (Rg), thickness of microregions with electron-density fluctuations (E) and distribution of particle sizes were investigated by SAXS.
2004, 22(4): 389-393
Abstract:
The direct polymerization of an unsymmetrical kink non-coplanar heterocyclic diamine (1) with various aromatic bis(trimellitimide)s (2a-e) using triphenyl phosphite and pyridine as condensing agents could generate a series of new aromatic poly(amide imide)s (3a-e) containing the kink non-coplanar phthalazinone heterocyclic units in the polymer main chains with inherent viscosities of 0.58-0.66 dL/g. The polymers are readily soluble in a variety of solvents such as N,N-dimethylformamide, N,N-dimethylacetamide, dimethyl sulfoxide, N-methyl-2-pyrrolidinone, pyridine and m-cresol and can be cast to form flexible and tough films. The glass transition temperatures of polymers (Tg) are in the range of 301-327℃,and the temperatures for 5% weight loss in nitrogen are in the range of 498-521 ℃.
The direct polymerization of an unsymmetrical kink non-coplanar heterocyclic diamine (1) with various aromatic bis(trimellitimide)s (2a-e) using triphenyl phosphite and pyridine as condensing agents could generate a series of new aromatic poly(amide imide)s (3a-e) containing the kink non-coplanar phthalazinone heterocyclic units in the polymer main chains with inherent viscosities of 0.58-0.66 dL/g. The polymers are readily soluble in a variety of solvents such as N,N-dimethylformamide, N,N-dimethylacetamide, dimethyl sulfoxide, N-methyl-2-pyrrolidinone, pyridine and m-cresol and can be cast to form flexible and tough films. The glass transition temperatures of polymers (Tg) are in the range of 301-327℃,and the temperatures for 5% weight loss in nitrogen are in the range of 498-521 ℃.
2004, 22(4): 395-398
Abstract:
A new kind of polyfluorene containing oxadiazole as the side chain was synthesized. The introduction of oxadiazole moiety as more bulky group prevents the aggregation and reduces the crystallinity of the polymers. Efficient intramolecular energy transfer from oxadiazole moiety to the conjugated backbone has been realized, leading to 70% improvement of photoluminescence quantum efficiency of the designed polymers. Compared with PAF, the PFOXD exhibits significant improvement in electroluminescence properties, with luminous efficiency of 0.8 cd/A and maximum luminance of 1800 cd/m2.
A new kind of polyfluorene containing oxadiazole as the side chain was synthesized. The introduction of oxadiazole moiety as more bulky group prevents the aggregation and reduces the crystallinity of the polymers. Efficient intramolecular energy transfer from oxadiazole moiety to the conjugated backbone has been realized, leading to 70% improvement of photoluminescence quantum efficiency of the designed polymers. Compared with PAF, the PFOXD exhibits significant improvement in electroluminescence properties, with luminous efficiency of 0.8 cd/A and maximum luminance of 1800 cd/m2.
2004, 22(4): 399-403
Abstract:
In order to improve the blood compatibility of silk fibroin (SF), poly(ethylene glycol) macromer (PEGM) in different amounts was added to the SF film to incorporate C=C group into the surface of blend films which were then modified by SO2 gas plasma treatment. ATR-FITR and XPS were used to analyze the chemical change which had occurred on the film's surface. When the content of sulfur on the surface of blend films surpasses 1.59%, the antithrombogenicity of plasma treated films increases remarkably due to surface sulfonation. This result implies that SF with blend of PEGM after SO2 plasma treatment have potential use for making blood-contacting biomaterials.
In order to improve the blood compatibility of silk fibroin (SF), poly(ethylene glycol) macromer (PEGM) in different amounts was added to the SF film to incorporate C=C group into the surface of blend films which were then modified by SO2 gas plasma treatment. ATR-FITR and XPS were used to analyze the chemical change which had occurred on the film's surface. When the content of sulfur on the surface of blend films surpasses 1.59%, the antithrombogenicity of plasma treated films increases remarkably due to surface sulfonation. This result implies that SF with blend of PEGM after SO2 plasma treatment have potential use for making blood-contacting biomaterials.
