氧化石墨烯/聚吡咯插层复合材料的制备和电化学电容性能

引用本文: 石琴, 门春艳, 李娟. 氧化石墨烯/聚吡咯插层复合材料的制备和电化学电容性能[J]. 物理化学学报, 2013, 29(08): 1691-1697. doi: 10.3866/PKU.WHXB201306031 shu

Citation: SHI Qin, MEN Chun-Yan, LI Juan. Preparation and Electrochemical Capacitance Properties of Graphene Oxide/Polypyrrole Intercalation Composite[J]. Acta Physico-Chimica Sinica, 2013, 29(08): 1691-1697. doi: 10.3866/PKU.WHXB201306031 shu

氧化石墨烯/聚吡咯插层复合材料的制备和电化学电容性能

基金项目:
新疆大学博士启动基金项目(BS110112) (BS110112)

乌鲁木齐科技计划项目(H101133001) (H101133001)

国家自然科学基金(21262035)资助 (21262035)

摘要:

以FeCl₃-甲基橙(MO)为模板, 通过化学原位聚合法成功制备出氧化石墨烯/聚吡咯( /PPy)插层复合材料. 采用X射线衍射(XRD)、傅里叶变换红外(FTIR)光谱、扫描电镜(SEM)和透射电镜(TEM)等测试技术对复合材料进行物性表征. 此外, 利用循环伏安、恒电流充放电和交流阻抗测试方法对复合材料在两种不同水系电解液(1 mol·L^-1 Na₂SO₄和1 mol·L^-1 H₂SO₄)中的电化学性能进行了研究. 结果显示: 氧化石墨烯和聚吡咯表现出各自优势并发挥协同作用, 使得 /PPy插层复合材料在中性和酸性电解液中都显示出可观的比电容. 电流密度为0.5 A·g^-1时, /PPy 插层复合材料在Na₂SO₄和H₂SO₄电解液中的比电容分别为449.1 和619.0 F·g^-1, 明显高于纯PPy的比电容. 经过800 次循环稳定性测试后, 两种不同电解液中, 复合材料初始容量的保持率分别为92%和62%. 其中酸性电解液体系中初始容量更大, 而中性溶液中具有更稳定的循环性能.

关键词:

English

Preparation and Electrochemical Capacitance Properties of Graphene Oxide/Polypyrrole Intercalation Composite

1.
College of Chemistry and Chemical Engineering, Xinjiang University, Urumqi 830046, P. R. China
Received Date: 08 March 2013
Available Online: 09 July 2013
Fund Project:
新疆大学博士启动基金项目(BS110112)

乌鲁木齐科技计划项目(H101133001)

国家自然科学基金(21262035)资助

Abstract:

Graphene oxide/polypyrrole ( /PPy) intercalation composite was successfully prepared via in-situ chemical oxidative polymerization of pyrrole monomers by using methyl orange (MO) as a template agent. The morphology and microstructure of the composite were characterized by X-ray diffraction (XRD) analysis, Fourier transform infrared (FTIR) spectroscopy, scanning electron microscopy (SEM), and transmission electron microscopy (TEM). In addition, the electrochemical properties of the composite material were investigated by cyclic voltammetry (CV), galvanostatic charge/discharge and electrochemical impedance spectroscopy techniques in two different aqueous electrolytes (1 mol·L^-1 Na₂SO₄ and 1 mol·L^-1 H₂SO₄). The results indicated that the /PPy intercalation composite displayed considerable specific capacitance in both neutral and acid electrolytes, which is attributed to taking full advantage of the superior properties and synergy of graphene oxide and polypyrrole. The /PPy intercalation composite exhibited the specific capacitance of 449.1 and 619.0 F·g^-1 in the Na₂SO₄ and H₂SO₄ electrolytes, respectively, at a current density of 0.5 A·g^-1. This is significantly higher than the corresponding specific capacitance of pure PPy. After 800 cycling test, the specific capacitance of the composite remained about 92% and 62% of the initial capacitance in the two different electrolytes, respectively. A higher initial capacitance was obtained in the acidic electrolyte, but the composite showed better electrochemical cyclic stability in the neutral electrolyte.

Key words:

1. [1]
  
  (1) Snook, G. A.; Kao, P.; Best, A. S. J. Power Sources 2011, 196,1. doi: 10.1016/j.jpowsour.2010.06.084
  (1) Snook, G. A.; Kao, P.; Best, A. S. J. Power Sources 2011, 196,1. doi: 10.1016/j.jpowsour.2010.06.084
2. [2]
  (2) Wang, G. P.; Zhang, L.; Zhang, J. J. Chem. Soc. Rev. 2012, 41,797. doi: 10.1039/c1cs15060j(2) Wang, G. P.; Zhang, L.; Zhang, J. J. Chem. Soc. Rev. 2012, 41,797. doi: 10.1039/c1cs15060j
3. [3]
  (3) Wang, J. P.; Xu, Y. L.; Zhu, J. B.; Ren, P. G. J. Power Sources2012, 208, 138. doi: 10.1016/j.jpowsour.2012.02.018(3) Wang, J. P.; Xu, Y. L.; Zhu, J. B.; Ren, P. G. J. Power Sources2012, 208, 138. doi: 10.1016/j.jpowsour.2012.02.018
4. [4]
  (4) Wang, J. P.; Xu, Y. L.;Wang, J.; Du, X. F. Synthetic Metals2011, 161, 1141. doi: 10.1016/j.synthmet.2011.01.011(4) Wang, J. P.; Xu, Y. L.;Wang, J.; Du, X. F. Synthetic Metals2011, 161, 1141. doi: 10.1016/j.synthmet.2011.01.011
5. [5]
  (5) Zhang, D. C.; Zhang, X.; Chen, Y.; Yu, P.;Wang, C. H.; Ma, Y.W. J. Power Sources 2011, 196, 5990. doi: 10.1016/j.jpowsour.2011.02.090(5) Zhang, D. C.; Zhang, X.; Chen, Y.; Yu, P.;Wang, C. H.; Ma, Y.W. J. Power Sources 2011, 196, 5990. doi: 10.1016/j.jpowsour.2011.02.090
6. [6]
  (6) Zhu, J. B.; Xu, Y. L.;Wang, J.;Wang, J. P. Acta Phys. -Chim. Sin. 2012, 28, 373. [朱剑波, 徐友龙, 王杰, 王景平. 物理化学学报, 2012, 28, 373.] doi: 10.3866/PKU.WHXB201112021(6) Zhu, J. B.; Xu, Y. L.;Wang, J.;Wang, J. P. Acta Phys. -Chim. Sin. 2012, 28, 373. [朱剑波, 徐友龙, 王杰, 王景平. 物理化学学报, 2012, 28, 373.] doi: 10.3866/PKU.WHXB201112021
7. [7]
  (7) Sahoo, S.; Nayak, G. C.; Das, C. K. Macromol. Symp. 2012,315, 177. doi: 10.1002/masy.v315.1(7) Sahoo, S.; Nayak, G. C.; Das, C. K. Macromol. Symp. 2012,315, 177. doi: 10.1002/masy.v315.1
8. [8]
  (8) Li, L. Y.; Xia, K. Q.; Li, L.; Shang, S. M.; Guo, Q. Z.; Yan, G. P.J. Nanopart. Res. 2012, 14, 908. doi: 10.1007/s11051-012-0908-3(8) Li, L. Y.; Xia, K. Q.; Li, L.; Shang, S. M.; Guo, Q. Z.; Yan, G. P.J. Nanopart. Res. 2012, 14, 908. doi: 10.1007/s11051-012-0908-3
9. [9]
  (9) Xu, J. J.;Wang, K.; Zu, S. Z.; Han, B. H.;Wei, Z. X. ACS Nano2010, 4, 5019. doi: 10.1021/nn1006539(9) Xu, J. J.;Wang, K.; Zu, S. Z.; Han, B. H.;Wei, Z. X. ACS Nano2010, 4, 5019. doi: 10.1021/nn1006539
10. [10]
  (10) Xu, C. H.; Sun, J.; Gao, L. J. Mater. Chem. 2011, 21, 11253.doi: 10.1039/c1jm11275a(10) Xu, C. H.; Sun, J.; Gao, L. J. Mater. Chem. 2011, 21, 11253.doi: 10.1039/c1jm11275a
11. [11]
  (11) Ding, B.; Lu, X. J.; Yuan, C. Z.; Yang, S. D.; Han, Y. Q.; Zhang,X. G.; Che, Q. Electrochimica Acta 2012, 62, 132. doi: 10.1016/j.electacta.2011.12.011(11) Ding, B.; Lu, X. J.; Yuan, C. Z.; Yang, S. D.; Han, Y. Q.; Zhang,X. G.; Che, Q. Electrochimica Acta 2012, 62, 132. doi: 10.1016/j.electacta.2011.12.011
12. [12]
  (12) Zhang, H. Y.; Hu, Z. A.; Zhang, F. H.; Liang, P. J.; Zhang, Y. J.;Yang, Y. Y.; Zhang, Z. Y.;Wu, H. Y. Chinese Journal of Applied Chemisty 2012, 29, 674. [张海英, 胡中爱, 张富海, 梁鹏举,张亚军, 杨玉英, 张子瑜, 吴红英. 应用化学, 2012, 29, 674.](12) Zhang, H. Y.; Hu, Z. A.; Zhang, F. H.; Liang, P. J.; Zhang, Y. J.;Yang, Y. Y.; Zhang, Z. Y.;Wu, H. Y. Chinese Journal of Applied Chemisty 2012, 29, 674. [张海英, 胡中爱, 张富海, 梁鹏举,张亚军, 杨玉英, 张子瑜, 吴红英. 应用化学, 2012, 29, 674.]
13. [13]
  (13) Zhu, C. Z.; Zhai, J. F.;Wen, D.; Dong, S. J. J. Mater. Chem.2012, 22, 6300. doi: 10.1039/c2jm16699b(13) Zhu, C. Z.; Zhai, J. F.;Wen, D.; Dong, S. J. J. Mater. Chem.2012, 22, 6300. doi: 10.1039/c2jm16699b
14. [14]
  (14) Chang, H. H.; Chang, C. K.; Tsai, Y. C.; Liao, C. S. Carbon2012, 50, 2331. doi: 10.1016/j.carbon.2012.01.056(14) Chang, H. H.; Chang, C. K.; Tsai, Y. C.; Liao, C. S. Carbon2012, 50, 2331. doi: 10.1016/j.carbon.2012.01.056
15. [15]
  (15) Yang, X. M.; Zhu, Z. X.; Dai, T. Y.; Lu, Y. Macromol. Rapid Commun. 2005, 26, 1736.(15) Yang, X. M.; Zhu, Z. X.; Dai, T. Y.; Lu, Y. Macromol. Rapid Commun. 2005, 26, 1736.
16. [16]
  (16) Tang, L. H.;Wang, Y.; Li, Y. M.; Feng, H. B.; Lu, J.; Li, J. H.Adv. Funct. Mater. 2009, 19, 2782. doi: 10.1002/adfm.v19:17(16) Tang, L. H.;Wang, Y.; Li, Y. M.; Feng, H. B.; Lu, J.; Li, J. H.Adv. Funct. Mater. 2009, 19, 2782. doi: 10.1002/adfm.v19:17
17. [17]
  (17) Feng, X. M.; Li, R. M.; Yan, Z. Z.; Liu, X. F.; Chen, R. F.; Ma,Y.W.; Li, X. A.; Fan, Q. L.; Huang,W. IEEE Transaction on Nanotechnology 2012, 11, 1080. doi: 10.1109/TNANO.2012.2200259(17) Feng, X. M.; Li, R. M.; Yan, Z. Z.; Liu, X. F.; Chen, R. F.; Ma,Y.W.; Li, X. A.; Fan, Q. L.; Huang,W. IEEE Transaction on Nanotechnology 2012, 11, 1080. doi: 10.1109/TNANO.2012.2200259
18. [18]
  (18) Fan, Z. J.; Kai,W.; Yan, J.;Wei, T.; Zhi, L. J.; Feng, J.; Ren, Y.M.; Song, L. P.;Wei, F. ACS Nano 2011, 5, 191. doi: 10.1021/nn102339t(18) Fan, Z. J.; Kai,W.; Yan, J.;Wei, T.; Zhi, L. J.; Feng, J.; Ren, Y.M.; Song, L. P.;Wei, F. ACS Nano 2011, 5, 191. doi: 10.1021/nn102339t
19. [19]
  (19) Zhang, L. L.; Zhao, S. Y.; Tian, X. N.; Zhao, X. S. Langmuir2010, 26, 17624. doi: 10.1021/la103413s(19) Zhang, L. L.; Zhao, S. Y.; Tian, X. N.; Zhao, X. S. Langmuir2010, 26, 17624. doi: 10.1021/la103413s
20. [20]
  (20) Gu, Z. M.; Li, C. Z.;Wang, G. C.; Zhang, L.; Li, X. H.;Wang,W. D.; Jin, S. L. Journal of Polymer Science Part B: Polymer Physics 2010, 48, 1329. doi: 10.1002/polb.v48:12(20) Gu, Z. M.; Li, C. Z.;Wang, G. C.; Zhang, L.; Li, X. H.;Wang,W. D.; Jin, S. L. Journal of Polymer Science Part B: Polymer Physics 2010, 48, 1329. doi: 10.1002/polb.v48:12
21. [21]
  (21) Hummers,W. S.; Offeman, R. E. J. Am. Chem. Soc. 1958, 80,1339. doi: 10.1021/ja01539a017(21) Hummers,W. S.; Offeman, R. E. J. Am. Chem. Soc. 1958, 80,1339. doi: 10.1021/ja01539a017
22. [22]
  (22) Zu, S. Z.; Han, B. H. J. Phys. Chem. C 2009, 113, 13651.(22) Zu, S. Z.; Han, B. H. J. Phys. Chem. C 2009, 113, 13651.
23. [23]
  (23) Meyer, J. C.; Geim, A. K.; Katsnelson, M. I.; Novoselov, K. S.;Obergfell, D.; Roth, S.; Girit, C.; Zettl, A. Solid State Communication 2007, 143, 101. doi: 10.1016/j.ssc.2007.02.047(23) Meyer, J. C.; Geim, A. K.; Katsnelson, M. I.; Novoselov, K. S.;Obergfell, D.; Roth, S.; Girit, C.; Zettl, A. Solid State Communication 2007, 143, 101. doi: 10.1016/j.ssc.2007.02.047
24. [24]
  (24) Tian, Y.; Yang, F. L.; Yang,W. S. Synthetic Metals 2006, 156,1052. doi: 10.1016/j.synthmet.2006.06.023(24) Tian, Y.; Yang, F. L.; Yang,W. S. Synthetic Metals 2006, 156,1052. doi: 10.1016/j.synthmet.2006.06.023
25. [25]
  (25) Cai, Y. M.; Qin, Z. Y.; Chen, L. Progress in Natural Science: Material International 2011, 21, 460. doi: 10.1016/S1002-0071(12)60083-5(25) Cai, Y. M.; Qin, Z. Y.; Chen, L. Progress in Natural Science: Material International 2011, 21, 460. doi: 10.1016/S1002-0071(12)60083-5
26. [26]
  (26) Sahoo, S.; Karthikeyan, G.; Nayak, G. C.; Das, C. K. Synthetic Metals 2011, 161, 1723.(26) Sahoo, S.; Karthikeyan, G.; Nayak, G. C.; Das, C. K. Synthetic Metals 2011, 161, 1723.
27. [27]
  (27) Zhang, K.; Zhang, L. L.; Zhao, X. S.;Wu, J. S. Chem. Mater.2010, 22, 1392. doi: 10.1021/cm902876u(27) Zhang, K.; Zhang, L. L.; Zhao, X. S.;Wu, J. S. Chem. Mater.2010, 22, 1392. doi: 10.1021/cm902876u
28. [28]
  (28) Sahoo, S.; Dhibar, S.; Das, C. K. Express Polymer Letters 2012,6, 965. doi: 10.3144/expresspolymlett.2012.102
  (28) Sahoo, S.; Dhibar, S.; Das, C. K. Express Polymer Letters 2012,6, 965. doi: 10.3144/expresspolymlett.2012.102

扫一扫看文章

计量

PDF下载量: 1289
文章访问数: 1126
HTML全文浏览量: 32

通讯作者: 陈斌, bchen63@163.com

1.
沈阳化工大学材料科学与工程学院沈阳 110142

氧化石墨烯/聚吡咯插层复合材料的制备和电化学电容性能

English

Preparation and Electrochemical Capacitance Properties of Graphene Oxide/Polypyrrole Intercalation Composite

CCS Chemistry：嵌段共聚物自组装成 “三明治”二维有机材料，实现纳米级压力传感功能

CCS Chemistry：颜徐州、鲍哲南：你的皮肤可能是一片SPMs

CCS Chemistry：工作高效不疲劳，只须让催化剂动起来

CCS Chemistry：静电组装导向聚合- 聚电解质纳米凝胶量化制备新策略

CCS Chemistry：金黄色葡萄球菌醛基脱氢酶是如何识别特异性底物的？

计量

通讯作者: 陈斌, bchen63@163.com

中国化学会秘书处

氧化石墨烯/聚吡咯插层复合材料的制备和电化学电容性能

English

Preparation and Electrochemical Capacitance Properties of Graphene Oxide/Polypyrrole Intercalation Composite

CCS Chemistry：嵌段共聚物自组装成 “三明治”二维有机材料，实现纳米级压力传感功能

CCS Chemistry：颜徐州、鲍哲南： 你的皮肤可能是一片SPMs

CCS Chemistry：工作高效不疲劳，只须让催化剂动起来

CCS Chemistry：静电组装导向聚合- 聚电解质纳米凝胶量化制备新策略

CCS Chemistry：金黄色葡萄球菌醛基脱氢酶是如何识别特异性底物的？

计量

文章相关

通讯作者: 陈斌, bchen63@163.com

中国化学会秘书处

CCS Chemistry：颜徐州、鲍哲南：你的皮肤可能是一片SPMs